| auszookers.com http://auszookers.com/forum/ |
|
| Rotary table/ bender stand. http://auszookers.com/forum/viewtopic.php?f=14&t=41312 |
Page 1 of 1 |
| Author: | Fatzook [ Sat Jun 08, 2013 6:47 pm ] |
| Post subject: | Rotary table/ bender stand. |
I found a use for the old NT 1.3 diff housings and axles!!!   Just cut the bearing housing off the end of the axle housing, and indexed it into some 75 x 5 SHS. Then the old axle is docked just past the bearing retainer, and dropped into the end. More pics tomorrow. |
|
| Author: | atari4x4 [ Sat Jun 08, 2013 6:51 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
i hope you're going to fit some LED's so you know how far to rotate it. 
|
|
| Author: | Fatzook [ Sat Jun 08, 2013 6:51 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
Fuck off idiot. This place is worse than Boost cruising! |
|
| Author: | Rusho [ Sat Jun 08, 2013 6:56 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
Fatzook wrote: Fuck off idiot. This place is worse than Boost cruising! 
|
|
| Author: | Fatzook [ Sat Jun 08, 2013 6:56 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
The post drops onto a 65x5SHS spigot in the bottom of the hole in the middle of the floor. 
|
|
| Author: | bigrig91 [ Sat Jun 08, 2013 7:00 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
Less picture taking more using the bender haha. Wish the shed looked like that now ^^^ |
|
| Author: | atari4x4 [ Sat Jun 08, 2013 7:00 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
Rusho wrote: Fatzook wrote: Fuck off idiot. This place is worse than Boost cruising! 
|
|
| Author: | 31zook [ Thu Jun 13, 2013 6:27 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
Hydro bender? |
|
| Author: | Fatzook [ Thu Jun 13, 2013 6:30 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
31zook wrote: Hydro bender? Hydro/ pnuematic. |
|
| Author: | 31zook [ Sun Jun 16, 2013 8:49 am ] |
| Post subject: | Re: Rotary table/ bender stand. |
Sweet! Was thinking the first bend you tried with it on a bearing would be funny to watch
|
|
| Author: | missmyljdaze [ Sun Jun 16, 2013 1:54 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
if you plan on using the bolt holes in the bearing housing's flange at any time, it might be a good idea to turn it 45 degrees before you weld it in place. stephen |
|
| Author: | Fatzook [ Sun Jun 16, 2013 5:18 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
31zook wrote: Sweet! Was thinking the first bend you tried with it on a bearing would be funny to watch Speedworks bender. Its verticle 
|
|
| Author: | Fatzook [ Sun Jun 16, 2013 5:19 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
missmyljdaze wrote: if you plan on using the bolt holes in the bearing housing's flange at any time, it might be a good idea to turn it 45 degrees before you weld it in place. stephen Nope. Already welded up. I just need to add a locking pin from the base to the table top to stop it rotating once in position. |
|
| Author: | Teracis [ Fri Jun 21, 2013 8:29 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
Nice slab on the floor bloke, looks much better than the dust/mudbowl! |
|
| Author: | Fatzook [ Fri Jun 21, 2013 11:45 pm ] |
| Post subject: | Re: Rotary table/ bender stand. |
Teracis wrote: Nice slab on the floor bloke, looks much better than the dust/mudbowl! I'll get a pic of it in the morning. The floor of a zulu's hut would be cleaner! |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|