Welcome to AZ!
I fitted Suzuki Swift seats to my Sierra. Cost me $200 for a complete set (including rear). They are as close to a bolt in fit as you will get.
| auszookers.com http://auszookers.com/forum/ |
|
| replacement seats http://auszookers.com/forum/viewtopic.php?f=37&t=37274 |
Page 1 of 2 |
| Author: | snowy [ Wed Nov 21, 2012 9:14 pm ] |
| Post subject: | replacement seats |
just got my daughter a Sierra and the front seats need replacing, they are completly worn out, had a quote of about $210 per seat to refurb, just wonderd if there were any seats I could pick up from the wreckers that will fit without to much modifying. Cheers Snowy |
|
| Author: | Scrawny [ Wed Nov 21, 2012 9:17 pm ] |
| Post subject: | Re: replacement seats |
Welcome to AZ! I fitted Suzuki Swift seats to my Sierra. Cost me $200 for a complete set (including rear). They are as close to a bolt in fit as you will get.
|
|
| Author: | snowy [ Wed Nov 21, 2012 9:37 pm ] |
| Post subject: | Re: replacement seats |
thanks for that, will stop by the wreckers tomorrow Snowy |
|
| Author: | Bucket [ Wed Nov 21, 2012 10:34 pm ] |
| Post subject: | Re: replacement seats |
Swift are the nicest seats i've sat in (in a sierra). I put them in my first one and this time I went autotechnica's and I'm regretting it already after driving it the past 2 days. Unless your body is really suited for the "race bucket seats", i'd highly recommend against them (unless they're of good quality or factory optioned buckets) |
|
| Author: | Gwagensteve [ Thu Nov 22, 2012 7:13 am ] |
| Post subject: | Re: replacement seats |
Bucket wrote: this time I went autotechnica's and I'm regretting it already after driving it the past 2 days. Unless your body is really suited for the "race bucket seats", i'd highly recommend against them (unless they're of good quality or factory optioned buckets) So much truth here. Swift GTi seats are ok I guess, iirc the seats in the photo above are Baleno GTX seats which are better constructed in my opinion, and fit well. I've also seen Mazda 323 astina sp seats in a Sierra and they were nice. I think the vast majority of cheap reclining "race" seats (they are no such thing) are rubbish. Steve. |
|
| Author: | KEENSY85 [ Thu Nov 22, 2012 7:41 am ] |
| Post subject: | Re: replacement seats |
Gwagensteve wrote: Bucket wrote: this time I went autotechnica's and I'm regretting it already after driving it the past 2 days. Unless your body is really suited for the "race bucket seats", i'd highly recommend against them (unless they're of good quality or factory optioned buckets) So much truth here. Swift GTi seats are ok I guess, iirc the seats in the photo above are Baleno GTX seats which are better constructed in my opinion, and fit well. I've also seen Mazda 323 astina sp seats in a Sierra and they were nice. I think the vast majority of cheap reclining "race" seats (they are no such thing) are rubbish. Steve. I agree here, I had a bloke buy my old zook ute shell and he was really excited about a pair of those seats, he pulled one off the ute apparently they were new they looked it, but they were crap, they had no padding it felt as if I was sitting on a towel on a bare seat and there didn't seem to be any seat adjustments. |
|
| Author: | jono165 [ Thu Nov 22, 2012 10:29 am ] |
| Post subject: | Re: replacement seats |
Gwagensteve wrote: I've also seen Mazda 323 astina sp seats in a Sierra and they were nice. Agreed on the mazda seats I have sat in a set of them before, very comfy. It is very hard to find them with side bolsters that arent torn up. These a from a Mazda BG Astina SP hatch which is about 1988-1994  I have N13 Pulsar seats in my zook. The sierra rails bolt straight on I just had to enlarge the holes slightly on the rails. Very easy install. Decent side bolslters so they sort of 'hug' you. They were $40 each from the wreckers, they are very common and seem to last pretty well. Pulsar Seats  Other option is go to the u-pull-it wreckers and just sit in a bunch of seats and find something comfy and work out how to fit it. |
|
| Author: | masterA [ Thu Nov 22, 2012 2:41 pm ] |
| Post subject: | Re: replacement seats |
Swift GTi seats are very comfy and one of the easiest to 'modify' to suit a sierra (so long as it't not a coily - post 96 model) You will just need to drill 2 new holes and elongate the ones that are already there....pretty much a bolt in job |
|
| Author: | snowy [ Tue Nov 27, 2012 8:55 pm ] |
| Post subject: | Re: replacement seats |
went to the wreckers, they wanted $400 for a pair of GTI seats, looked at Autotechnicas $300 for a pair, are the really that bad? Has any one tried TF Rodeo seats |
|
| Author: | jdk81 [ Wed Nov 28, 2012 4:41 am ] |
| Post subject: | Re: replacement seats |
snowy wrote: looked at Autotechnicas $300 for a pair, are the really that bad? They are terrible. I bought mine, and it had autotechnica seats in it. They were junk. I installed baleno seats ($80 the pair). |
|
| Author: | Gwagensteve [ Wed Nov 28, 2012 7:23 am ] |
| Post subject: | Re: replacement seats |
Wrecker economics are rarely wrong. Yes, a $200 second hand GTi seat is actually better than a new $150 autotechinca pile. As for rodeo- maybe they would work, maybe not. There are enough options on here that don't require too much work that you'd need a food reason to start from scratch with a seat that hasn't been mentioned. Steve. |
|
| Author: | Trypt [ Wed Nov 28, 2012 9:17 am ] |
| Post subject: | Re: replacement seats |
I used barina seats. (same model as the swift) i used the sierra rails and welded them to base of swift seat. for $30 im not complaining. in fact id go as far to say thats the best value money purchase i made since i bought the sierra. |
|
| Author: | Samwich [ Wed Nov 28, 2012 11:39 am ] |
| Post subject: | Re: replacement seats |
Any bolt in swaps for the front of a 95 shorty VIT? 
|
|
| Author: | atari4x4 [ Wed Nov 28, 2012 11:46 am ] |
| Post subject: | Re: replacement seats |
 bolt in optioni have recaro's sitting on pete's seat mounts, they is very nice. 
|
|
| Author: | krat [ Wed Nov 28, 2012 1:11 pm ] |
| Post subject: | Re: replacement seats |
Samwich wrote: Any bolt in swaps for the front of a 95 shorty VIT? I will also follow this one with interest for my 95 SWB. My stock seats now have wire poking out of them, so I have to pad them with towels to stop some serious body part damage. Kev. |
|
| Author: | Samwich [ Wed Nov 28, 2012 1:14 pm ] |
| Post subject: | Re: replacement seats |
Look at the post above, No go on the bolt in for the shorty vits... |
|
| Author: | oohsam [ Tue Dec 04, 2012 9:02 am ] |
| Post subject: | Re: replacement seats |
I'm itching for some of fatzook's brackets for seats, but not sure when he's free enough to fab me up some. Poor bloke is as busy as a prostitute at a bucks night. |
|
| Author: | Scrawny [ Tue Dec 04, 2012 9:09 am ] |
| Post subject: | Re: replacement seats |
oohsam wrote: I'm itching for some of fatzook's brackets for seats, but not sure when he's free enough to fab me up some. Poor bloke is as busy as a prostitute at a bucks night. I'm right behind you!!! Well.... not literally..... |
|
| Author: | gvzookdriver [ Mon Dec 31, 2012 10:20 am ] |
| Post subject: | Re: replacement seats |
I have found some baleno seats like the swift ones above. My guess would be they are the exact same but just want to double check. I'm just looking to see if these will fit a sierra with minimal stress Look something like this 
|
|
| Author: | oohsam [ Mon Dec 31, 2012 10:53 am ] |
| Post subject: | Re: replacement seats |
They look the same as my swift GTI seats. Pretty much identical. |
|
| Author: | Benny90 [ Mon Jan 07, 2013 8:18 am ] |
| Post subject: | Re: replacement seats |
Mine has Honda CRX seats in it. They are very nice to sit in and they hug you in place nice. |
|
| Author: | Gwagensteve [ Mon Jan 07, 2013 8:27 am ] |
| Post subject: | Re: replacement seats |
I understand CRX seats are excellent, but it can be hard to find them in good condition as they are lightly constructed and wear quickly with heavy (i.e western) people sitting in them. Same goes for MX-5 seats, moreso because they are a convertible and tend to get more sun damage. Steve. PS I have now seen that late GTi seats are pretty much the same as Baleno GTX seats. IMHO they are much better built than early GTi seats - they feel much more robust. |
|
| Author: | Ace [ Mon Jan 07, 2013 3:40 pm ] |
| Post subject: | Re: replacement seats |
Gwagensteve wrote: Wrecker economics are rarely wrong. Yes, a $200 second hand GTi seat is actually better than a new $150 autotechinca pile. As for rodeo- maybe they would work, maybe not. There are enough options on here that don't require too much work that you'd need a food reason to start from scratch with a seat that hasn't been mentioned. Steve. Now I feel like an ass for stopping at $50 for a full gti interior on a recent auction as the competition bidding against it was a tool when I tried to buy stuff off him.... Yes I am part Scottish - hence the 413 purchase 
|
|
| Author: | gvzookdriver [ Thu Jan 10, 2013 4:37 pm ] |
| Post subject: | Re: replacement seats |
When fitting seats do you use the standard rails or the rails that come with the seat?? I have the baleno glx seat (Look the same as GTI seats) that I mentioned above and bolted the sierra rails to it but when I tried to fit them to the car they are sitting to wide for the standard mounting holes pictures in my build gvzookdriver wrote: Tried to install baleno GLX seats today
What rails dose everyone use the ones that come with the seats or the sierra rails (baleno rails seem too long) Drivers side - Lined up near the tunnel  Way off near door   Bolted to the bottom  Passenger side holes aren't even close to lining up   What have I done wrong ? |
|
| Author: | philc81 [ Tue Jan 15, 2013 5:52 pm ] |
| Post subject: | Re: replacement seats |
does any one know if the sierra seat mounts changed much through the series? i have an 81 model and have found that most seats have the same problems as gvzookdriver. |
|
| Author: | philc81 [ Tue Jan 15, 2013 5:52 pm ] |
| Post subject: | Re: replacement seats |
does any one know if the sierra seat mounts changed much through the series? i have an 81 model and have found that most seats have the same problems as gvzookdriver. |
|
| Author: | jono165 [ Tue Jan 15, 2013 7:54 pm ] |
| Post subject: | Re: replacement seats |
I'm pretty sure they remained the same. I have n13 pulsar seats which were slightly wider than the standard mounts with the Sierra rails. Mine weren't as far out as gvzookdrivers. I only had to drill 2 holes about 20mm further out on the drivers side and managed to get the passenger side to fit with no mods. |
|
| Author: | Ace [ Thu Jan 17, 2013 2:01 pm ] |
| Post subject: | Re: replacement seats |
@ GVZook, get some 20 - 30 flat maybe 10 - 12 thick you need to make up a square frame... you can drill n tap or countersink it etc but you end up with a set of bolts that point up to bolt into the seat spacing and a set facing down to align with the orig seat rail wldth / bolt to both and hey presto. The reason I mention 10+mm is to countersink opposite's to clear seat movement or drill n tap and weld the head of some HT studding into the "square" also check legality in your highly legislated country. Hope this helps |
|
| Author: | Gwagensteve [ Thu Jan 17, 2013 3:16 pm ] |
| Post subject: | Re: replacement seats |
philc81 wrote: does any one know if the sierra seat mounts changed much through the series? i have an 81 model and have found that most seats have the same problems as gvzookdriver. Drivers side is the same on all leaf spring cars. Passenger side has a different on a 1.0 litre, but it's easy to drill new holes in the floor to run 1.3 runners. 1.3 seats bolt to the 1.0 tilt mechanism regardless. Steve. |
|
| Author: | gvzookdriver [ Fri Jan 18, 2013 8:23 pm ] |
| Post subject: | Re: replacement seats |
Ace wrote: @ GVZook, get some 20 - 30 flat maybe 10 - 12 thick you need to make up a square frame... you can drill n tap or countersink it etc but you end up with a set of bolts that point up to bolt into the seat spacing and a set facing down to align with the orig seat rail wldth / bolt to both and hey presto. The reason I mention 10+mm is to countersink opposite's to clear seat movement or drill n tap and weld the head of some HT studding into the "square" also check legality in your highly legislated country. Hope this helps Thanks mate I have worked it all out just needed to take a step back breathe n measure a few things and now it all fits 
|
|
| Page 1 of 2 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|