| auszookers.com http://auszookers.com/forum/ |
|
| Carby G13 http://auszookers.com/forum/viewtopic.php?f=37&t=40885 |
Page 1 of 1 |
| Author: | Toppy [ Tue May 14, 2013 3:00 pm ] |
| Post subject: | Carby G13 |
Hey guys I have a g13a out of a barina to go into my zook. Will the carby off the 1.3 swift fit onto it? Sent from my GT-I9300 using Tapatalk 2 |
|
| Author: | want33s [ Tue May 14, 2013 4:00 pm ] |
| Post subject: | Re: Carby G13 |
Barina and Swift are same so YES a Swift carby will fit a Barina motor. |
|
| Author: | Toppy [ Tue May 14, 2013 5:25 pm ] |
| Post subject: | Re: Carby G13 |
Awesome. Just wanting to check. Cheers Sent from my GT-I9300 using Tapatalk 2 |
|
| Author: | coily96 [ Tue May 14, 2013 9:01 pm ] |
| Post subject: | Re: Carby G13 |
Let us know how you go as a suzuki shop told me their a different carby to the sierra. |
|
| Author: | want33s [ Tue May 14, 2013 9:23 pm ] |
| Post subject: | Re: Carby G13 |
coily96 wrote: Let us know how you go as a suzuki shop told me their a different carby to the sierra. That is correct. Barina/Swift carby is different to Sierra. It has a lot more pollution gear on it. Cable setup is different. Air hat is different. Not sure about the mounting bolts. The OP's question isn't too clear. |
|
| Author: | Toppy [ Wed May 15, 2013 7:52 am ] |
| Post subject: | Re: Carby G13 |
What more do you need to know? I have a G13a motor and I can purchase a carby from a g13ba swift. I was told there is more bits that dont need to be connected but apprently should still work? Sent from my GT-I9300 using Tapatalk 2 |
|
| Author: | Zook_Fan [ Wed May 15, 2013 10:19 am ] |
| Post subject: | Re: Carby G13 |
What is the G13a motor going in? If it's the sierra that you have in your profile than you won't want a swift carby. They are overly complicated and have a heap of pollution gear on it. The inlet manifold is different and possibly the mounting bolts as want33s has said. If it's going in a swift or barina than use it, if it's going in a sierra get a sierra carby and inlet manifold. |
|
| Author: | Toppy [ Wed May 15, 2013 1:29 pm ] |
| Post subject: | Re: Carby G13 |
Its going in my zook but it is a motor from a Barina apparently. I got the inlet manifold from the same person selling the carby so I am assuming it should all bolt togethet. Sent from my GT-I9300 using Tapatalk 2 |
|
| Author: | want33s [ Wed May 15, 2013 1:42 pm ] |
| Post subject: | Re: Carby G13 |
Don't waste your time trying to fit a Swift/Barina carby to a Sierra manifold or trying to make a FWD manifold work in a RWD car. |
|
| Author: | fordem [ Thu May 16, 2013 2:11 am ] |
| Post subject: | Re: Carby G13 |
The FWD intake has the water outlet on the left side if fitted in the original east-west configuration, which translates to the rear of the engine in a north-south installation, the RWD intake has it at the front. |
|
| Author: | Toppy [ Thu May 16, 2013 7:20 am ] |
| Post subject: | Re: Carby G13 |
Turns out I was wrong. The manifold I have is a Sierra one. Cheers guys. Sent from my GT-I9300 using Tapatalk 2 |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|