Hi guys,
Sorry to hear stockman. Photos below of the current flanges. Only have to grind a couple of mm off the bent engine mount
| auszookers.com http://auszookers.com/forum/ |
|
| Sierra G16B extractors http://auszookers.com/forum/viewtopic.php?f=37&t=42890 |
Page 1 of 1 |
| Author: | azzas15 [ Tue Sep 10, 2013 4:23 pm ] |
| Post subject: | Sierra G16B extractors |
Hey Gents, Had a look around and did some searches but I seem to find more info just on the flanges. Just in the process of doing a g16B swap using one from a Baleno and just thinking about the exhaust. I found these extractors on eBay but they note its for a sierra with a Vitara G16B I assume they would be similar bit would they suit a Baleno G16B? Link below http://bit.ly/13DDShK Cheers, Azza |
|
| Author: | atari4x4 [ Tue Sep 10, 2013 4:25 pm ] |
| Post subject: | Re: Sierra G16B extractors |
they're essentially the same motor apart from the baleno intake differs, pretty sure they are the ones that everyone uses for G16b powered sierra's. |
|
| Author: | azzas15 [ Tue Sep 10, 2013 4:57 pm ] |
| Post subject: | Re: Sierra G16B extractors |
Sweet. Thanks for the quick reply. Payday this Friday so i will be buying this and a new set of body mounts Cheers Azza |
|
| Author: | coily96 [ Wed Sep 11, 2013 8:29 pm ] |
| Post subject: | Re: Sierra G16B extractors |
MPH are quick with postage and ive had my set for a few years and had no problems. |
|
| Author: | Wazz [ Thu Sep 12, 2013 8:57 pm ] |
| Post subject: | Re: Sierra G16B extractors |
I had issues with them. Ended up buying some off low range. Heaps better. |
|
| Author: | atari4x4 [ Thu Sep 12, 2013 9:08 pm ] |
| Post subject: | Re: Sierra G16B extractors |
in MPH's defence, you seem to have issues with everything... brake lines, PS brackets, headers, steering arms, etc, etc. |
|
| Author: | azzas15 [ Fri Sep 27, 2013 10:46 am ] |
| Post subject: | Re: Sierra G16B extractors |
Got the extractors yesterday and they are well made for $200 |
|
| Author: | stockman [ Fri Sep 27, 2013 10:58 am ] |
| Post subject: | Re: Sierra G16B extractors |
I had a set from Rod too. I asked for a custom setup comprising of Sierra extractors on a Vitara flange with a o2 bung. (well before he offered them as a set) Was really disappointed with what I got. The flange was roughly cut, the pipes themselves wanted to sit 10mm into my engine mount and the whole thing seemed very freehand. I hope now that he is offering this as a complete unit he has a jig setup and is pumping out quality not kwality. |
|
| Author: | Gwagensteve [ Fri Sep 27, 2013 11:24 am ] |
| Post subject: | Re: Sierra G16B extractors |
I have used wildcat and lukey extractors without a problem. A tiny but of engine mount flange grinding on the removable bracket that sits in the chassis. Steve. |
|
| Author: | azzas15 [ Fri Sep 27, 2013 12:53 pm ] |
| Post subject: | |
Hi guys, Sorry to hear stockman. Photos below of the current flanges. Only have to grind a couple of mm off the bent engine mount
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|