Nope[youtube][/youtube] bottom of Victoria the very bottom
| auszookers.com http://auszookers.com/forum/ |
|
| Maruti ute http://auszookers.com/forum/viewtopic.php?f=37&t=53192 |
Page 1 of 1 |
| Author: | dlrowmas [ Wed Sep 07, 2016 7:08 pm ] |
| Post subject: | Maruti ute |
I have just acquired a 1999 stockman ute with a genuine 35000 km on it .. no rust but has been used as a fencing vehicle on a rural farm so is in need of a new bonnet and left and right guard. Thats where the noob question comes in . Do i have to buy parts off a wide track 1l or will 1.3l bonnet and guards fit. Do the guards come seperate or do i replace the whole clip, and does anyone do a fibreglass clip and bonnet ? Was planning on selling it but after a couple of stuff arounds im just gonna keep it i think. |
|
| Author: | greavesyzook [ Thu Sep 08, 2016 7:29 am ] |
| Post subject: | Re: Maruti ute |
I'll buy it off you haha |
|
| Author: | Gwagensteve [ Thu Sep 08, 2016 10:38 am ] |
| Post subject: | Re: Maruti ute |
Any leaf sprung clip and bonnet will fit Guards can be swapped but they are brazed to the front facia so they can be tough to separate. |
|
| Author: | sideways [ Thu Sep 08, 2016 12:40 pm ] |
| Post subject: | Re: Maruti ute |
The panels can be bought new for reasonable prices (relative term), 4wdproducts sell them. As steve says, 1.3l stuff goes right on. Dunno if it will have the mounts for the airbox ect though? |
|
| Author: | Gwagensteve [ Thu Sep 08, 2016 12:46 pm ] |
| Post subject: | Re: Maruti ute |
Good point- the jack mount will be on the wrong side and there'll be no provision for the 1.0 airbox. There may be some fibreglass available from QLD or NZ but it would be a struggle to see any advantage unless your favourite things are cracks, wonky panels and running separate earths for everything. |
|
| Author: | dlrowmas [ Thu Sep 08, 2016 4:21 pm ] |
| Post subject: | Re: Maruti ute |
Thanks guys , my only reason for thinking about glass panels was so far im not a fan of the 0.00003 mm thick steel they seem to have used, i have no issue making brackets and cutting stuff , i just didnt want to waste time chasing up panels that wont fit .. greavesyzook ... show me some money and its yours .. fly up here , i will pick you up from the airport and if you buy it i will take your flight cost off the price |
|
| Author: | dlrowmas [ Thu Sep 08, 2016 7:20 pm ] |
| Post subject: | Re: Maruti ute |
Is your name ewan by any chance greavesyzook ? |
|
| Author: | Gwagensteve [ Thu Sep 08, 2016 8:26 pm ] |
| Post subject: | Re: Maruti ute |
That thin steel makes it light, so the gap between it and glass is negligible. Steve. |
|
| Author: | dlrowmas [ Fri Sep 09, 2016 5:26 am ] |
| Post subject: | Re: Maruti ute |
Fair point |
|
| Author: | greavesyzook [ Fri Sep 09, 2016 6:34 am ] |
| Post subject: | Re: Maruti ute |
No its josh haha but most people call me greavesy |
|
| Author: | rustyzook [ Sat Sep 10, 2016 8:06 am ] |
| Post subject: | Re: Maruti ute |
Get a 1l clip, put your wt flares on. The you have all your mounts. Or sell me the ute. |
|
| Author: | dlrowmas [ Sat Sep 10, 2016 8:49 pm ] |
| Post subject: | Re: Maruti ute |
Happy to sell you the ute, show me the money |
|
| Author: | rustyzook [ Sat Sep 10, 2016 11:45 pm ] |
| Post subject: | Re: Maruti ute |
Where are you and how much? |
|
| Author: | dlrowmas [ Sun Sep 11, 2016 6:50 am ] |
| Post subject: | Re: Maruti ute |
Utes out at the farm ... half an hour west of casino on the bruxner highway $4000 firm |
|
| Author: | rustyzook [ Sun Sep 11, 2016 7:59 am ] |
| Post subject: | Re: Maruti ute |
Too far for me, I'd love it but. If you find 1L stuff it will fit, as will 1.3 but as said the mounts will be wrong |
|
| Author: | dlrowmas [ Sun Sep 11, 2016 8:19 am ] |
| Post subject: | Re: Maruti ute |
Cheers |
|
| Author: | rustyzook [ Sun Sep 11, 2016 8:54 am ] |
| Post subject: | Re: Maruti ute |
No worries, when I say mounts will be wrong I'm talking about airbox as the 1.3 run a diffrent style airbox, how ever the jack should be the same I cannot remember. |
|
| Author: | dlrowmas [ Sun Sep 11, 2016 5:12 pm ] |
| Post subject: | Re: Maruti ute |
None of that matters, i can make a mount and brackets its just the physical panel dimensions i was concerned about |
|
| Author: | dlrowmas [ Wed Sep 14, 2016 6:02 pm ] |
| Post subject: | Re: Maruti ute |
Rustyzook , i hate this ute , im 6 foot 6 tall and even with no seats in it i cant fit my legs in ... i have bought a secongd hand arb bullbar and alloy tray , if your legitimately interested i would deliver the thing to your door and still for 4k |
|
| Author: | greavesyzook [ Wed Sep 14, 2016 7:04 pm ] |
| Post subject: | Re: Maruti ute |
Deliver it to me for 4k lol.... |
|
| Author: | dlrowmas [ Wed Sep 14, 2016 7:12 pm ] |
| Post subject: | Re: Maruti ute |
Dont tempt me ... do you live in the golden triangle ? |
|
| Author: | greavesyzook [ Wed Sep 14, 2016 7:19 pm ] |
| Post subject: | Re: Maruti ute |
| Nope[youtube][/youtube] bottom of Victoria the very bottom
|
|
| Author: | dlrowmas [ Wed Sep 14, 2016 7:42 pm ] |
| Post subject: | Re: Maruti ute |
Got a hot (or unattractive but easy) single ( or unhappily married) sister ? |
|
| Author: | dlrowmas [ Wed Sep 14, 2016 7:43 pm ] |
| Post subject: | Re: Maruti ute |
Fuck it ... $4000 and i will pay freight to your nesrest transport depot |
|
| Author: | rustyzook [ Sun Sep 18, 2016 7:52 am ] |
| Post subject: | Re: Maruti ute |
Any pics? |
|
| Author: | dlrowmas [ Sun Sep 18, 2016 2:56 pm ] |
| Post subject: | Re: Maruti ute |
        And as it looks after putting the tray, bullbar and new wheels and tyres on it today 
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|