Im pretty sure no...
Nothing fits a coily
| auszookers.com http://auszookers.com/forum/ |
|
| WT centre into coily diff housing http://auszookers.com/forum/viewtopic.php?f=5&t=11304 |
Page 1 of 1 |
| Author: | JCZOOK [ Wed Apr 21, 2010 3:03 am ] |
| Post subject: | WT centre into coily diff housing |
Will a wt centre fit into a coily front diff housing?? |
|
| Author: | Junior_91 [ Wed Apr 21, 2010 3:04 am ] |
| Post subject: | Re: WT centre into coily diff housing |
Im pretty sure no... Nothing fits a coily
|
|
| Author: | flaxton123 [ Wed Apr 21, 2010 3:19 am ] |
| Post subject: | Re: WT centre into coily diff housing |
i read something about it the other day but i didnt take much notice because it was about a coily bahahah sorry mate maybe look in the tech section |
|
| Author: | Rusho [ Wed Apr 21, 2010 10:28 am ] |
| Post subject: | Re: WT centre into coily diff housing |
No.....coily front is the reverse pinion type. Not sure of it's technical terminology, either way, no. |
|
| Author: | BlueSuzy [ Wed Apr 21, 2010 1:27 pm ] |
| Post subject: | Re: WT centre into coily diff housing |
YES It will fit. You will have to move the steering arms. (unsure what you can use to change the hub arms, More reasearch needed) Coily is Hipinion so arms run under diff centre. WT is low pinion. |
|
| Author: | Damo [ Wed Apr 21, 2010 1:32 pm ] |
| Post subject: | Re: WT centre into coily diff housing |
BlueSuzy wrote: YES It will fit.
You will have to move the steering arms. (unsure what you can use to change the hub arms, More reasearch needed) Coily is Hipinion so arms run under diff centre. WT is low pinion. To clarify BlueSuzy's point, the tie rod on a coily runs behind the diff. The diff centre is a high pinion type and the tie rod runs underneath that. If you were to fit a WT diff centre you would not be able to fit the tie rod back on. |
|
| Author: | BlueSuzy [ Wed Apr 21, 2010 1:36 pm ] |
| Post subject: | Re: WT centre into coily diff housing |
Damo wrote: BlueSuzy wrote: YES It will fit. You will have to move the steering arms. (unsure what you can use to change the hub arms, More reasearch needed) Coily is Hipinion so arms run under diff centre. WT is low pinion. To clarify BlueSuzy's point, the tie rod on a coily runs behind the diff. The diff centre is a high pinion type and the tie rod runs underneath that. If you were to fit a WT diff centre you would not be able to fit the tie rod back on. Thanks 
(Its too early, i just woke up)
At least i got the YES right unlike the rest of the nOoBs 
|
|
| Author: | tanshi [ Wed Apr 21, 2010 1:40 pm ] |
| Post subject: | Re: WT centre into coily diff housing |
will WT swivel hubs fit? use the tie rod draglink and stuff from a WT |
|
| Author: | BlueSuzy [ Wed Apr 21, 2010 2:04 pm ] |
| Post subject: | Re: WT centre into coily diff housing |
tanshi wrote: will WT swivel hubs fit?
Use the tie rod draglink and stuff from a WT Have heard the coily's wheel track is wider. so draglink and stuff will have to use custom or coily. Arms unsure. (i thinkk there was talk about this not long ago, or i think it was for a jimny mainly.) 
|
|
| Author: | Ben_Sierra [ Wed Apr 21, 2010 3:36 pm ] |
| Post subject: | Re: WT centre into coily diff housing |
instead of going to all this trouble, why not just dump the coily and buy a WT...  
|
|
| Author: | Rusho [ Wed Apr 21, 2010 7:58 pm ] |
| Post subject: | Re: WT centre into coily diff housing |
So it fits but it's too much dicking about to make it work. What's the point! If you want it for lokka reasons modify a jimny air lokka. Problem solvered!! |
|
| Author: | tanshi [ Wed Apr 21, 2010 8:36 pm ] |
| Post subject: | Re: WT centre into coily diff housing |
if you could do it with bolt on bits it would be very little dicking around. |
|
| Author: | ZookiMonsta [ Wed Apr 21, 2010 9:47 pm ] |
| Post subject: | Re: WT centre into coily diff housing |
WT swivel hubs fit coily, Jimny front diff center fits coily front (allowing coilys to run 4.1 diff ratios  ) and yes a WT diff center will fit in the
front if you change the swivel hub, but I'm not sure if WT axles and Coily axles have the same spline. |
|
| Author: | BlueSuzy [ Wed Apr 21, 2010 11:31 pm ] |
| Post subject: | Re: WT centre into coily diff housing |
Have you put the baby 1L size jimny front into the 1.3 size front housing?! Jimny is 4.09 ratio. |
|
| Author: | Junior_91 [ Thu Apr 22, 2010 1:38 am ] |
| Post subject: | Re: WT centre into coily diff housing |
Well ok then something fits a coily
|
|
| Author: | JCZOOK [ Thu Apr 22, 2010 2:22 am ] |
| Post subject: | Re: WT centre into coily diff housing |
I have a WT not a coily. I'm just beginning to nut out a coil conversion and Ive been told the coilys run a better wheel bearing setup. And maybe some steering advantages??? |
|
| Author: | BlueSuzy [ Thu Apr 22, 2010 2:36 am ] |
| Post subject: | Re: WT centre into coily diff housing |
Running a coily front end is ALL disadvantages. Search all the problems coilys have. |
|
| Author: | joeblow [ Thu Apr 22, 2010 2:39 am ] |
| Post subject: | Re: WT centre into coily diff housing |
JCZOOK wrote: I have a WT not a coily. I'm just beginning to nut out a coil conversion and Ive been told the coilys run a better wheel bearing setup. And maybe some steering advantages???
no they don't, if anything its a little worse for larger wheels. they are the same as a vitara. and steeing is no better, just more of a pain if you want to run different ratios. |
|
| Author: | JCZOOK [ Thu Apr 22, 2010 2:42 am ] |
| Post subject: | Re: WT centre into coily diff housing |
Ok cool thanks for clearing it up |
|
| Author: | KEENSY85 [ Sun May 13, 2012 1:38 am ] |
| Post subject: | Re: WT centre into coily diff housing |
awsome thread iv got a nt and the hole point of these beast is budget budget and hagling for parts so what we have or find ,its funny u find mod cut swap all effort low cost is the way. but anyway i just striped a coily so i have coily diffs if i can make wt centres fit i m goinng to truss these diffs and and weld all the perchers and crap on so ok all crap aside the diffs centre will defently bolt in |
|
| Author: | want33s [ Sun May 13, 2012 9:32 am ] |
| Post subject: | Re: WT centre into coily diff housing |
84 NT.... 1.0 or 1.3? |
|
| Author: | Fatzook [ Sun May 13, 2012 10:54 am ] |
| Post subject: | Re: WT centre into coily diff housing |
You will need a custom drag link and tie rod. WT ones are not long enough. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|