See the bit in pic, will give you an idea how it comes out.
Same as the bit on a single stick, but didn't couldn't find a picture
| auszookers.com http://auszookers.com/forum/ |
|
| Transfer removal http://auszookers.com/forum/viewtopic.php?f=5&t=15945 |
Page 1 of 1 |
| Author: | maloo11 [ Fri Oct 15, 2010 5:38 am ] |
| Post subject: | Transfer removal |
In the process of taking out my transfer case (never done before). How do you get the small metal clamp off at the bottom of the lever? Does it split with a screwdriver? |
|
| Author: | Ben_Sierra [ Fri Oct 15, 2010 5:47 am ] |
| Post subject: | Re: Transfer removal |
Push down and twist. |
|
| Author: | Gwagensteve [ Fri Oct 15, 2010 5:57 am ] |
| Post subject: | Re: Transfer removal |
Are you talking about the hose clamp thingy that holds the rubber boot on? if so, there is a little tab folded over that holds it tight. Find the tab and open it up with a screwdriver. (It's kind of a like a compressed Z shape and unfolds) Steve. |
|
| Author: | maloo11 [ Fri Oct 15, 2010 5:58 am ] |
| Post subject: | Re: Transfer removal |
Ok. thanks |
|
| Author: | Gwagensteve [ Fri Oct 15, 2010 5:59 am ] |
| Post subject: | Re: Transfer removal |
See my post above. Steve. |
|
| Author: | maloo11 [ Fri Oct 15, 2010 6:27 am ] |
| Post subject: | Re: Transfer removal |
Ok guys, my shift lever aint moving. Boot is off and i can see the spring, everything done according to haynes manual, but the lever wont budge. i push down and turn and NOTHING. Does it need a helping hand with the hammer? |
|
| Author: | christover1 [ Fri Oct 15, 2010 6:33 am ] |
| Post subject: | Re: Transfer removal |
I always left my stick on, when dropping t-case. It was easier to get at stick on the floor. But make sure you push and twist on the bottom piece, not the stick itself |
|
| Author: | christover1 [ Fri Oct 15, 2010 6:41 am ] |
| Post subject: | Re: Transfer removal |
See the bit in pic, will give you an idea how it comes out. Same as the bit on a single stick, but didn't couldn't find a picture
|
|
| Author: | maloo11 [ Fri Oct 15, 2010 6:46 am ] |
| Post subject: | Re: Transfer removal |
Got it. Thanks for your help. |
|
| Author: | Hotshot993 [ Mon Sep 19, 2011 3:55 am ] |
| Post subject: | Re: Transfer removal |
Hey my transfer lever is stuck in neutral. Trying to get that spring loaded thing off. I push down, turn anti clockwise. Should pop up all the way and stick should just pull out or what do I do. Been at it for last 30mins trying to twist it and get the thing off but nothing so far. Also it's really hard to twist that spring loaded thing. |
|
| Author: | stockman [ Mon Sep 19, 2011 3:57 am ] |
| Post subject: | Re: Transfer removal |
Just make sure you are pushing down hard enough. Also when taking the case out I find it easier to leave the stick in and put it into 4x4 low. |
|
| Author: | Hotshot993 [ Mon Sep 19, 2011 4:01 am ] |
| Post subject: | Re: Transfer removal |
I'm not taking the case out. Just need the stick out. And I got it turned a bit and it still won't pop up:/ |
|
| Author: | Hotshot993 [ Mon Sep 19, 2011 4:07 am ] |
| Post subject: | Re: Transfer removal |
It like got to a certain part and t won't go any further. But won't pop up either |
|
| Author: | Hotshot993 [ Mon Sep 19, 2011 4:11 am ] |
| Post subject: | Re: Transfer removal |
Got it thanks. Just the spring wasn't pushing it up it was stuck. |
|
| Author: | stockman [ Mon Sep 19, 2011 4:19 am ] |
| Post subject: | Re: Transfer removal |
That was for the other guy. Use a couple of flat head screwdrivers. |
|
| Author: | Hotshot993 [ Mon Sep 19, 2011 5:06 am ] |
| Post subject: | Re: Transfer removal |
The problem is that it's like jammed between two gears and I need to try and line up the two gaps inside the transfer case so I get get the lever in there. If you kind of get what I mean:/ |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|