As Liz pointed out in this thread also http://auszookers.com/index.php?name=Fo ... ic&t=15938
The problem is no boobs
| auszookers.com http://auszookers.com/forum/ |
|
| Whats Wrong with this Picture? http://auszookers.com/forum/viewtopic.php?f=5&t=16227 |
Page 1 of 1 |
| Author: | toeragz [ Tue Oct 26, 2010 3:22 am ] |
| Post subject: | Whats Wrong with this Picture? |
Ok so I'm replacing my rear bearings and seals. Just need to know something. Reading through this thread and he says watch out for small spacer washer, between brake plate and bearing. http://auszookers.com/index.php?name=Ne ... cle&sid=17 So are the bearings in my pic like a closed bearing or is that my washer in the wrong spot. Cant see any other washer? Unless its tucked in the other side of the bearing? Cheers for the help |
|
| Author: | Ben_Sierra [ Tue Oct 26, 2010 3:23 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
As Liz pointed out in this thread also http://auszookers.com/index.php?name=Fo ... ic&t=15938 The problem is no boobs
|
|
| Author: | shep [ Tue Oct 26, 2010 3:30 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
toeragz what you have there is right. just replace the same way and you will be laughing. |
|
| Author: | shep [ Tue Oct 26, 2010 3:31 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
hay ben, why dont you fuck off for a bit? do ya need to be a tosser in every thread ya open? |
|
| Author: | toeragz [ Tue Oct 26, 2010 3:34 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
Ok problem solved |
|
| Author: | Ben_Sierra [ Tue Oct 26, 2010 3:39 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
shep wrote: hay ben, why dont you fuck off for a bit? do ya need to be a tosser in every thread ya open?
Fuck shep whats crawled up your ass... Nothing wrong with a bit of humour every now and again... |
|
| Author: | jonno_racing [ Tue Oct 26, 2010 3:43 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
Not when people are asking for help you douch. yeah thats right. make suer u have the seal point outwoods, mine was backwoods (prev owner) and caused a MASIVE bearing fail! |
|
| Author: | Ben_Sierra [ Tue Oct 26, 2010 3:46 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
Sorry guys, I didn't realise that you had to be a miserable prick when someone wants some help.... |
|
| Author: | jonno_racing [ Tue Oct 26, 2010 3:52 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
nah but just helping them would help. especily when its a simple question thats easy to ask. |
|
| Author: | steak_knife [ Tue Oct 26, 2010 7:18 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
 Bleeder nipple's at the bottom??
That small spacer is on the n/t ( narrow track) sierra's, the w/t's have it built in.. |
|
| Author: | toeragz [ Tue Oct 26, 2010 8:22 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
steak_knife wrote: :? Bleeder nipple's at the bottom??
That small spacer is on the n/t ( narrow track) sierra's, the w/t's have it built in.. Bleeders where its meant to be  just took the photo upside down
car is a n/t, could it be a w/t bearing? |
|
| Author: | steak_knife [ Tue Oct 26, 2010 8:25 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
Can you get a pic between the backing plate & the bearing?? |
|
| Author: | toeragz [ Tue Oct 26, 2010 7:09 pm ] |
| Post subject: | Re: Whats Wrong with this Picture? |
its a tight squeeze for my camera lol |
|
| Author: | weaves [ Tue Oct 26, 2010 11:34 pm ] |
| Post subject: | Re: Whats Wrong with this Picture? |
That most definately is a WT bearing, as long as the seperate spacer from the NT setup was removed (which it appears to have been done) you have no worries. Just in future, always buy the WT bearings so you have the inbuilt spacer, or you will need to source a spacer seperately as it doesn't come with the kits. weaves |
|
| Author: | toeragz [ Tue Oct 26, 2010 11:58 pm ] |
| Post subject: | Re: Whats Wrong with this Picture? |
alright so I better get some w/t bearings
glad I asked before I went and bought some n/t. Thanks for the help guys |
|
| Author: | steak_knife [ Wed Oct 27, 2010 6:21 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
& don't forget to put the backing plate on BEFORE you fit the bearing's..
Done that before.. 
|
|
| Author: | toeragz [ Wed Oct 27, 2010 8:33 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
yeh try not forget that one
cheers again fella's |
|
| Author: | Zook_Fan [ Wed Oct 27, 2010 8:44 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
would there be any negative effects if the backing plate was modified so that the bearing could slide through the centre of it? so you don't have to remove the brakes to get the rear axle out |
|
| Author: | losfer [ Wed Oct 27, 2010 8:48 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
yeah the backing plate holds it in , to stop it from sliding out whilst driving .. |
|
| Author: | Zook_Fan [ Wed Oct 27, 2010 8:48 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
yeah that makes sense, didn't think that through... 
|
|
| Author: | watermouse [ Wed Oct 27, 2010 7:09 pm ] |
| Post subject: | Re: Whats Wrong with this Picture? |
steak_knife wrote: :P & don't forget to put the backing plate on BEFORE you fit the bearing's..
Done that before.. X2 Freaked out that i was going to have to grind off a perfectly new bearing. I made a special tool that I could use in the press to "pull" the new bearing off. Its a shame it doesn't fit when there is a backing plate on there, other wise that would be the best way to get them off. In this case tight is not nice. I doubt I will the use the tool again. If any one gets too excited like I did and pushes the new bearing on without the plate, give me a bell. Ill send the tool. 
|
|
| Author: | royce [ Wed Oct 27, 2010 7:41 pm ] |
| Post subject: | Re: Whats Wrong with this Picture? |
Zook_Fan wrote: would there be any negative effects if the backing plate was modified so that the bearing could slide through the centre of it? so you don't have to remove the brakes to get the rear axle out
1 litres can do this, the americans like to mod the backing plates and run the 1 litre axle retainers so this can be done |
|
| Author: | steak_knife [ Wed Oct 27, 2010 7:46 pm ] |
| Post subject: | Re: Whats Wrong with this Picture? |
royce wrote: Zook_Fan wrote: would there be any negative effects if the backing plate was modified so that the bearing could slide through the centre of it? so you don't have to remove the brakes to get the rear axle out 1 litres can do this, the americans like to mod the backing plates and run the 1 litre axle retainers so this can be done Lowrange sell them.. 
|
|
| Author: | toeragz [ Thu Oct 28, 2010 7:05 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
another question guys Is the w/t seal different to a n/t. Just that my bearing seems in pretty good shape and can't see any major problems with it. Think its the seal thats causing the diff oil to leak. Any pics on the forum of some seals or any info is greatly appreciated 
|
|
| Author: | losfer [ Thu Oct 28, 2010 7:43 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
its usually the bearing gone that makes the seal leak , but unlike front wheel bearings where you can grab the top and bottom of the tyre and feel play , you usually wont feel this play on a rear bearing , but if you jack up the car , and put both hands under the tyre and lift the wheel you will usually feel up and down movement. ohh and the seal is the same n/t and w/t.. |
|
| Author: | toeragz [ Thu Oct 28, 2010 8:10 am ] |
| Post subject: | Re: Whats Wrong with this Picture? |
cheers mate |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|