| auszookers.com http://auszookers.com/forum/ |
|
| Couple of G13BB questions.. http://auszookers.com/forum/viewtopic.php?f=5&t=17220 |
Page 1 of 1 |
| Author: | superduki [ Thu Dec 02, 2010 8:19 am ] |
| Post subject: | Couple of G13BB questions.. |
G'day chaps, Quick question Does anyone know what or how the idle is controlled on a g13bb, Mine idles high, and I'd like to bring it down. Sometimes it idles fine, other times its 1500 odd. No I don't have a vaccuum leak either. Next question, does anyone know the tacho output on the ecu? I don't have one at the moment, And i'd like to wire it up to the sierra dash if possible. That is all Thanks 
|
|
| Author: | inbits [ Thu Dec 02, 2010 8:21 am ] |
| Post subject: | Re: Couple of G13BB questions.. |
im pretty sure the g13bb ecu wont work with the sierra tacho |
|
| Author: | Brenno [ Thu Dec 02, 2010 11:44 pm ] |
| Post subject: | Re: Couple of G13BB questions.. |
I'm glad you are getting around to fixing these problems! When I had it, it never idled that high. Have you got a Jimny service manual? I think Spamwell hooked up his sierra with a jimny tacho input, dont know how though. |
|
| Author: | want33s [ Fri Dec 03, 2010 12:08 am ] |
| Post subject: | Re: Couple of G13BB questions.. |
Sams Coily had an aftermarket tacho fitted. |
|
| Author: | BlueSuzy [ Fri Dec 03, 2010 12:18 am ] |
| Post subject: | Re: Couple of G13BB questions.. |
I use a baleno one, with the baleno twin coil motor... The g13bbs are twin coil also. So they should be similar. Tried hunting down a jim cluster? |
|
| Author: | tobeszook [ Fri Dec 03, 2010 8:20 pm ] |
| Post subject: | Re: Couple of G13BB questions.. |
i don't know if this helps but my g16b started to idle high( and running a bit rough) i just gave it a full service now its back to normal |
|
| Author: | tobeszook [ Fri Dec 03, 2010 8:24 pm ] |
| Post subject: | Re: Couple of G13BB questions.. |
tuffcoily is parting out a jimny with a g13bb |
|
| Author: | superduki [ Wed Dec 08, 2010 9:23 am ] |
| Post subject: | Re: Couple of G13BB questions.. |
Hmmm, may possibly have to do some investigation myself then! Currently it has four bent rods. Hydraulic'd it in a river on saturday, Machine shop has bits coming for it, should have new rods, rings & bearings friday arvo. Then I'll be back onto the idle issue and tacho. Has anyone got a jimny ecu pin out for g13bb? and / or service manual? Cheers guys, Simon. |
|
| Author: | atari4x4 [ Wed Dec 08, 2010 9:24 am ] |
| Post subject: | Re: Couple of G13BB questions.. |
pics of your variable compression rods... |
|
| Author: | royce [ Wed Dec 08, 2010 9:34 am ] |
| Post subject: | Re: Couple of G13BB questions.. |
g16b does this when the MAF is a bit dirty, are they a similar setup? |
|
| Author: | superduki [ Wed Dec 08, 2010 9:56 am ] |
| Post subject: | Re: Couple of G13BB questions.. |
atari4x4 wrote: pics of your variable compression rods...
you have the pic i took Gus, you upload it, I haven't taken it off my iDingle to my laptop yet! |
|
| Author: | superduki [ Wed Dec 08, 2010 9:58 am ] |
| Post subject: | Re: Couple of G13BB questions.. |
royce wrote: g16b does this when the MAF is a bit dirty, are they a similar setup?
Nope, map unfortunately. One thing I did notice is the idle is alot lower when the alternator is connected, but I've checked my charge rate and sense wire to the alt, and is working fine! |
|
| Author: | steak_knife [ Wed Dec 08, 2010 10:15 am ] |
| Post subject: | Re: Couple of G13BB questions.. |
Re-set your base idle, it should have a air bypass screw in the throttle body, just unplug the IAC & adjust the screw till you get the idle you want, then plug it back in.. I run mine disconnected all the time, just run's off base idle, even with P/s.. |
|
| Author: | atari4x4 [ Wed Dec 08, 2010 10:18 am ] |
| Post subject: | Re: Couple of G13BB questions.. |
superduki wrote: atari4x4 wrote: pics of your variable compression rods... you have the pic i took Gus, you upload it, I haven't taken it off my iDingle to my laptop yet! it's still stuck inside my iFail 4... 
|
|
| Author: | superduki [ Wed Dec 08, 2010 10:19 am ] |
| Post subject: | Re: Couple of G13BB questions.. |
steak_knife wrote: Re-set your base idle, it should have a air bypass screw in the throttle body, just unplug the IAC & adjust the screw till you get the idle you want, then plug it back in..
I run mine disconnected all the time, just run's off base idle, even with P/s.. Thanks mate, thats exactly what I was after! Once I put it back together (hopefully sunday, but have my work chrissy dinner sat night) I'll try that! |
|
| Author: | Brenno [ Wed Dec 08, 2010 2:15 pm ] |
| Post subject: | Re: Couple of G13BB questions.. |
I have a jimny manual I think however it is 5000km east of me at the moment, I get back from Perth Sunday so during the week one night - or just google one
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|