auszookers.com :: View topic - running 33s

auszookers.com http://auszookers.com/forum/

running 33s http://auszookers.com/forum/viewtopic.php?f=5&t=18518	Page 1 of 2

Author:	TryHard [ Tue Jan 25, 2011 1:44 am ]
Post subject:	running 33s
hey i have question for those people running 33s spoa and spua ... iv been having big think about plans for zook and i want to run 33s but im just not sure what whats the best to go about it i see two ways to fix my prob ... run spoa with 33s and off set rims or spacers or i could buy ubolt flip kit and underbody slide / bash plate and also use wheel spacers / offset rims i see both sides of story but does anyone have any input with ideas this car still needs to run on the road its not daylie driveer only drives on weekend to track and back... ideas thanks

Author:	tanshi [ Tue Jan 25, 2011 1:46 am ]
Post subject:	Re: running 33s
i have 33s on my lj50 with only 2 inch springs spua, spoa isnt needed for only 33s do a virtual lift, and 2 inch spring lift,

Author:	TryHard [ Tue Jan 25, 2011 1:49 am ]
Post subject:	Re: running 33s
tanshi wrote: i have 33s on my lj50 with only 2 inch springs spua, spoa isnt needed for only 33s do a virtual lift, and 2 inch spring lift, virtul lift ?

Author:	tanshi [ Tue Jan 25, 2011 1:51 am ]
Post subject:	Re: running 33s
check out JRzooks build thread you remove body panels around the guards to allow the 33 to fit. and keeping the car low

Author:	TryHard [ Tue Jan 25, 2011 1:59 am ]
Post subject:	Re: running 33s
hey i just had a look at his build first of it looks great but i noticed some things first of i dont think hes running 33s if he is they look rather small they look like 31s.. 2nd i do not have the time or fab skils to do what he done i think i would more then likely do a body lift insted of that .. anyways lol it does look good but the zook is no bigger then mine

Author:	tanshi [ Tue Jan 25, 2011 2:07 am ]
Post subject:	Re: running 33s
the point was to show you virtual lift. not the 33s body lift is another way to go. if you dont have the fab skills for a virtual lift. then dont even attempt spoa

Author:	TryHard [ Tue Jan 25, 2011 2:13 am ]
Post subject:	Re: running 33s
tanshi wrote: the point was to show you virtual lift. not the 33s body lift is another way to go. if you dont have the fab skills for a virtual lift. then dont even attempt spoa yer thanks tanshi umm i was gona get a mate of mine thats works as a welder to do the spoa welds

Author:	Fatzook [ Tue Jan 25, 2011 2:29 am ]
Post subject:	Re: running 33s
I am part of the way through this process at the moment, although a little different. However the clearance issues remain the same. My intended setup is 33's (which I have) and a sizeable guard chop to ensure that only 2-3" of lift are needed to clear the 33's. I am running links and coilovers, so height can be adjusted down quite low. I do not believe in body lifts. No matter which path you choose, 33's are a big job to fit when SPUA, and installing SPOA is also VERY involved to get it right. Just ensure that you have the skills and budget to see this through BEFORE you start.

Author:	Fatzook [ Tue Jan 25, 2011 2:30 am ]
Post subject:	Re: running 33s
TryHard wrote: i was gona get a mate of mine thats works as a welder to do the spoa welds Welding is the easy part. Its the setup thats crutial.

Author:	TryHard [ Tue Jan 25, 2011 2:50 am ]
Post subject:	Re: running 33s
Fatzook wrote: TryHard wrote: i was gona get a mate of mine thats works as a welder to do the spoa welds Welding is the easy part. Its the setup thats crutial. thanks fatzook but do u have any advice about the setup u would run and i dont think my budget would be to much of a issue im also gona take the car to suzuki store hopefully they can put my lockrights in and il get them to tell me what they think on the set up

Author:	Fatzook [ Tue Jan 25, 2011 3:00 am ]
Post subject:	Re: running 33s
At the end of the day, it comes down to what YOU want. Personally I hate the idea of a tall sierra. So thats why I'm shooting for the same height as an SPUA sierra on 33's. If it were my car, and I was insisting on 33's, i'd have airlocker rear, moly axles and cv's, WT diffs with NT spring spacing, -25 or better wheels, and 2" lifted springs with RUF. Extended shackles if needed, but the most important part.....virtual lift. Its a big job, but well worth the effort. Also another thing to consider when lifting a sierra. If you lift it an inch, widen it by the same. Stability is very under-rated.

Author:	tanshi [ Tue Jan 25, 2011 3:02 am ]
Post subject:	Re: running 33s
its not a sierra but the theory is the same as this. the more you can chop the guards the less work you will have to do else where to fit them. my lj50 on 33s

Author:	TryHard [ Tue Jan 25, 2011 3:05 am ]
Post subject:	Re: running 33s
Also another thing to consider when lifting a sierra. If you lift it an inch, widen it by the same. Stability is very under-rated.[/quote] o yes dont worry i no this haha my plan was basicly to run spoa with 33 maxxis bighorns i think there 265x12 .. my current ones are 245x10 i think lol plus i want to put 2 inch wheel spacers in or offset rims seeing that i will be driving this zook on the road 2 a from the tracks and down the freeway i need it to be stable hence why i also will be going wider also i was going to take a leaf out of every packet from my EFS springs to allow it to sag right down also i will prob move my front dif fwd ...

Author:	TryHard [ Tue Jan 25, 2011 3:06 am ]
Post subject:	Re: running 33s
tanshi wrote: its not a sierra but the theory is the same as this. the more you can chop the guards the less work you will have to do else where to fit them. my lj50 on 33s thats a nice looking lj50 i must say dont see many did u get the bonet tie downs of lowrange off road ?

Author:	CairnsZook [ Tue Jan 25, 2011 3:29 am ]
Post subject:	Re: running 33s
Here's another thread on the same topic. http://www.auszookers.com/index.php?nam ... pic&t=2390 2 and a half years later and I'm still on 29's... One day I'll get there

Author:	tanshi [ Tue Jan 25, 2011 3:30 am ]
Post subject:	Re: running 33s
the bonnet tie downs are standard ones with a slightly modified top handle

Author:	TryHard [ Tue Jan 25, 2011 3:35 am ]
Post subject:	Re: running 33s
CairnsZook wrote: Here's another thread on the same topic. http://www.auszookers.com/index.php?nam ... pic&t=2390 2 and a half years later and I'm still on 29's... One day I'll get there thanks for that il give it a read

Author:	BlueSuzy [ Tue Jan 25, 2011 4:32 am ]
Post subject:	Re: running 33s
Wheel spacers are illegal. but so are 33's. Spua. BFH, move diffs forward and back, Shaft extensions, 2" spring, 2" BL, Possible bump extensions.

Author:	LAY80N [ Tue Jan 25, 2011 5:09 am ]
Post subject:	Re: running 33s
33x12 Boggers (closer to 34's) can fit on a car with SPUA dead flat springs and a 2 inch BL and some panel work Layto....

Author:	appsie [ Tue Jan 25, 2011 9:39 pm ]
Post subject:	Re: running 33s
pics layto?? or is that your brothers thing that stretched??

Author:	31zook [ Tue Jan 25, 2011 9:53 pm ]
Post subject:	Re: running 33s
33x14.5 1-0inch lift springs, 50mm bodylift, and hammering the guards, didn't ride so good, but it was stable beyond belief..... 33x12.5

Author:	31zook [ Tue Jan 25, 2011 9:56 pm ]
Post subject:	Re: running 33s
check layton's build, it in there the tin top above was sold to the guy who built the red half cut first...

Author:	appsie [ Tue Jan 25, 2011 9:58 pm ]
Post subject:	Re: running 33s
what about ya uber gay shackles in that pic josh,providing some lift haha. did look cool like that

Author:	31zook [ Tue Jan 25, 2011 10:03 pm ]
Post subject:	Re: running 33s
i built those drop shackles long ago, like 3years ago, they worked well, and were pinned, if i built a new set i would design them differently but were good enough for me... i sold em to suzukilwb on here....

Author:	skyman [ Wed Jan 26, 2011 3:21 am ]
Post subject:	Re: running 33s
If ya can handle the body work i would say the a virtual lift is the best way to go. Get as much as you can out of the virtual lift, and then use the spring (spring under) to get the rest. I run spring over because it was easiest for me at the time. If I could go back to spring under without loosing a lot of sheetmetal I would be therein a heartbeat. 34's spring under virtual lift, lowest rig I have seen on 34's aside from a linked up one.

Author:	Gwagensteve [ Wed Jan 26, 2011 9:17 am ]
Post subject:	Re: running 33s
35's, No body or spring lift, no bumpstop spacing (really - the front 'stops are vitara rears but they are positioned to the same height as stock. They are inboarded though). This car runs RUF and NT front spring spacing. Quote: if you dont have the fab skills for a virtual lift. then dont even attempt spoa That's the truth. It's far easier to chop some metal out the way than it is to modify steering, driveshafts, shock mounts etc associated with SPOA. Whilst it's true that that hardtop in the pic has steering, shock and bumpstop mods these are due to the RUF, and those mods would be getting done regardless of the tyre size being run. Steve.

Author:	31zook [ Wed Jan 26, 2011 9:26 am ]
Post subject:	Re: running 33s
wow, no inner guard, thats new on a bonneted car. loving that truck, pure practicality

Author:	Gwagensteve [ Wed Jan 26, 2011 9:39 am ]
Post subject:	Re: running 33s
31zook wrote: wow, no inner guard, thats new on a bonneted car. It's pretty common. I've knocked a couple of sets of inners out on club cars. It's just a tyre clearance thing, but normally, the tyre catches the headlight once the inner guard comes out. The car in the pics above has a narrowed front end so the tyres clear the headlights- easy once the inner guards come out. (A nightmare with them in) Steve.

Author:	TryHard [ Thu Jan 27, 2011 12:12 am ]
Post subject:	Re: running 33s
Gwagensteve wrote: 31zook wrote: wow, no inner guard, thats new on a bonneted car. It's pretty common. I've knocked a couple of sets of inners out on club cars. It's just a tyre clearance thing, but normally, the tyre catches the headlight once the inner guard comes out. The car in the pics above has a narrowed front end so the tyres clear the headlights- easy once the inner guards come out. (A nightmare with them in) Steve. thanks for the pics yer iv decided not to go spoa but i was thinking of doing 2 inch body and taking a grinder to it .. u have inspired me lol just a Q how hard is that innner gaurd to remove is it road legal to remove it ... anyideas what i would need to chop to fit the 33s btw thanks for the advice everyone

Author:	Gwagensteve [ Fri Jan 28, 2011 7:49 am ]
Post subject:	Re: running 33s
I would normally body lift a car to run 33's. The owner of the hardtop in the pics didn't want a BL, so he did more chopping. You'd need to check with an engineer in your state to confirm if removing the inner guards is legal. ( Might be.. might not be. As sierras have a chassis, the inner guards aren't deemed structural) Generally though, I'd say it's not a good idea in any case. It's more work than it looks - the air filter and battery need to be moved. In the case of the car in the pics, the battery is an optima and it's on it side, set through the floor, under the seat on the passengers side. Also, the wiring, washer bottle and some other widgetry needs to be moved. After all that, the engine is much more exposed to water splashes, debris like sticks coming into the engine bay and throwing belts, increasing mud through the alternator etc. With 33's and a 2" BL, (and I'll assume stock front springs and bumpstop location) you won't need to cut the guards anywhere near as much as the car in the pics. cutting straight from the highest point on the inner guard to the guard should be plenty. You will want to move the front axle forward though. Without doing a RUF, it's quite possible to redrill spring plates to bring the axle forward about 30mm - plenty for what you need. (That's what I've done) Steve.

Page 1 of 2	All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/