auszookers.com
http://auszookers.com/forum/

Door sill mould
http://auszookers.com/forum/viewtopic.php?f=5&t=195		 Page 1 of 1
Author:  ANNODAM [ Fri Jul 28, 2006 5:11 pm ]
Post subject:  Door sill mould
OK this is hard to describe.

The plastic black sill mould just below the drivers side door of my Vitara is up the shit & needs replacing. So I called around some places & found one but they tell me it comes in 3 sections & from looking at the sill mould from a distance it appears like it does. However, on closer inspection (under the car) it resembles (to me) to be one whole long piece bolted at either end with some plastic clips in the middle.

So my question is, are these people correct in saying there are 3 pieces?
Author:  royce [ Fri Jul 28, 2006 6:20 pm ]
Post subject:  Re: Door sill mould
mine has a long centre section and then 2 little caps either end

I would say thats what they mean?
Author:  ANNODAM [ Fri Jul 28, 2006 7:12 pm ]
Post subject:  Re: Door sill mould
Yes exactly like mine, but is it infact one piece or 3?

Maybe I should just piss off the shitty sill moulds & get side steps instead....
Author:  royce [ Fri Jul 28, 2006 7:46 pm ]
Post subject:  Re: Door sill mould
thats my plan, the plastic just causes rust anyway
Author:  antt [ Fri Jul 28, 2006 11:52 pm ]
Post subject:  Re: Door sill mould
its 3 piece. i pulled the front most section off mine when i chopped the guards, to cut it to suit, then screwed it back on
Author:  ANNODAM [ Sat Jul 29, 2006 1:56 pm ]
Post subject:  Re: Door sill mould
Right OK thanks!

If that's the case then, I only need 2 pieces.
Author:  Granta [ Wed Nov 22, 2006 10:55 pm ]
Post subject:  Re: Door sill mould
I bashed my sil a week or two ago 4x4ing, went around yesterday to get a few quotes to fix it, and ppl quoted me any where from 1600, to 700. But what im wondering is, could i just put some side steps on it and not even worry about the sill ???
Author:  Troll [ Wed Nov 22, 2006 11:04 pm ]
Post subject:  Re: Door sill mould
yeah just do it. can you still open and close the door?
Author:  Granta [ Thu Nov 23, 2006 12:40 am ]
Post subject:  Re: Door sill mould
yea.
Any ideas on designe?
Author:  royce [ Thu Nov 23, 2006 12:48 am ]
Post subject:  Re: Door sill mould
in my thread and westies theres a few :wink:
Author:  Granta [ Thu Nov 23, 2006 1:00 am ]
Post subject:  Re: Door sill mould
where can i find your thread ?
Author:  royce [ Thu Nov 23, 2006 1:05 am ]
Post subject:  Re: Door sill mould
scroll through the introduce yourself section, in there somewhere
Author:  Granta [ Thu Nov 23, 2006 1:18 am ]
Post subject:  Re: Door sill mould
oh yea, there pretty nice. I like westies better sorry royce.

How do they go when the chasie is flexing ? and how long did they take to make and install ???
Author:  royce [ Thu Nov 23, 2006 1:29 am ]
Post subject:  Re: Door sill mould
not built for looks, I'm used to a sill 20cm higher so made em to take a flogging

I did em over a week between other stuff but a big day would see em done, less if you do em like westies without the extra bar

chassis dont flex :wink:
Author:  Granta [ Thu Nov 23, 2006 1:45 am ]
Post subject:  Re: Door sill mould
Cheers :D
Also just testing your knowledge on the chassis :P hehe
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/