auszookers.com
http://auszookers.com/forum/

quick spotlight wiring question
http://auszookers.com/forum/viewtopic.php?f=5&t=20150		 Page 1 of 1
Author:  sierra_1988 [ Sat Mar 19, 2011 9:17 am ]
Post subject:  quick spotlight wiring question
wires coming from harness: white= pos, black= neg. Wires from spotlights are blue+brown. Am I correct that blue is negative? Cheers.
Author:  Scrawny [ Sat Mar 19, 2011 9:20 am ]
Post subject:  Re: quick spotlight wiring question
Doesn't matter
Author:  royce [ Sat Mar 19, 2011 9:23 am ]
Post subject:  Re: quick spotlight wiring question
yeah it does if they are earthed as well

got a multi meter? see if both have continuity to the mounting bolt, lowest resistance is likely positive

or open em and see
Author:  sierra_1988 [ Sat Mar 19, 2011 9:37 am ]
Post subject:  Re: quick spotlight wiring question
thanks for quick replies.
Author:  royce [ Sat Mar 19, 2011 9:40 am ]
Post subject:  Re: quick spotlight wiring question
oops highest resistance :oops:
Author:  Scrawny [ Sat Mar 19, 2011 9:44 am ]
Post subject:  Re: quick spotlight wiring question
Who earths their lights through the mounting bolt as well as an earth wire out the back?

And if I had to choose, I'd say brown was neg
Author:  royce [ Sat Mar 19, 2011 9:59 am ]
Post subject:  Re: quick spotlight wiring question
ive seen heaps of lights have an earth lead as well as a metal housing thats connected to teh bulb earth
Author:  zook95 [ Sat Mar 19, 2011 10:00 am ]
Post subject:  Re: quick spotlight wiring question
yeh as far as i can think brown is neg
Author:  sierra_1988 [ Sat Mar 19, 2011 11:19 am ]
Post subject:  Re: quick spotlight wiring question
Thanks for the replies, guys, but terms like "I think", "if I choose", really don't give me any confidence. It is a Nite Stalker HID set, comes with wiring harness. All is connected according to instructions, but I still need to connect the Balck and white from harness to the brown and blue coming out of the lights. Could I do damage if I go "eany, meany, miny, mo? :?
Author:  fordem [ Sat Mar 19, 2011 12:47 pm ]
Post subject:  Re: quick spotlight wiring question
sierra_1988 wrote:
Could I do damage if I go "eany, meany, miny, mo? :?


Assuming it's properly fused - worst case scenario you'll blow the fuse.
Author:  89_tintop [ Sat Mar 19, 2011 8:21 pm ]
Post subject:  Re: quick spotlight wiring question
shouldnt do any damage.. they just wont work one way.

I would work with brown being - (it is extremely common to use it as - )

I have played with few hid set ups that were meant to be plug and play but were far from it.. the little kid putting them together got the plug completely wrong...
figured it and got it cirrect with no damage to the kits.
Author:  Scrawny [ Sat Mar 19, 2011 8:40 pm ]
Post subject:  Re: quick spotlight wiring question
Obviously the instructions don't explain which is which?
Author:  lump_a_charcoal [ Sat Mar 19, 2011 8:46 pm ]
Post subject:  Re: quick spotlight wiring question
In 240v land, brown would be active, and blue would be neutral.
In your case, it may not matter.

Open up the light fitting and see where the wires run to, and get back to us.
Author:  Scrawny [ Sat Mar 19, 2011 8:49 pm ]
Post subject:  Re: quick spotlight wiring question
lump_a_charcoal wrote:
In 240v land, brown would be active, and blue would be neutral.
In your case, it may not matter.

Open up the light fitting and see where the wires run to, and get back to us.


Don't confuse to poor lad with 240v land!! :lol:
Author:  stocker [ Sat Mar 19, 2011 8:50 pm ]
Post subject:  Re: quick spotlight wiring question
if you have 2 wires coming out the back of the light then you should be 99% sure that its not connected to the metal chassis of the light on either.

And lights aren't Polarity sensitive seeing as they are just a Resistor that gets hot :)
Author:  whincup [ Sat Mar 19, 2011 8:57 pm ]
Post subject:  Re: quick spotlight wiring question
stocker wrote:
if you have 2 wires coming out the back of the light then you should be 99% sure that its not connected to the metal chassis of the light on either.

And lights aren't Polarity sensitive seeing as they are just a Resistor that gets hot :)


what about HIDs? they the same?
Author:  stocker [ Sat Mar 19, 2011 9:08 pm ]
Post subject:  Re: quick spotlight wiring question
whincup wrote:
stocker wrote:
what about HIDs? they the same?


Are you asking a question about the way HID's Work?

Or Asking About wiring them?

I am not familiar with wiring HID's so i couldn't tell you

as to the way they work.
This website should explain alot better than I can

http://www.essortment.com/high-intensit ... 12677.html
Author:  lump_a_charcoal [ Sat Mar 19, 2011 9:13 pm ]
Post subject:  Re: quick spotlight wiring question
whincup wrote:
stocker wrote:
if you have 2 wires coming out the back of the light then you should be 99% sure that its not connected to the metal chassis of the light on either.

And lights aren't Polarity sensitive seeing as they are just a Resistor that gets hot :)


what about HIDs? they the same?


No.

I would still be going with the brown...
Author:  Rusho [ Sat Mar 19, 2011 9:23 pm ]
Post subject:  Re: quick spotlight wiring question
ScrawnC wrote:
lump_a_charcoal wrote:
In 240v land, brown would be active, and blue would be neutral.
In your case, it may not matter.

Open up the light fitting and see where the wires run to, and get back to us.


Don't confuse to poor lad with 240v land!! :lol:


I posted exactly the same thing last night then decided to delete as I didn't want to cause confusion :lol:
Author:  dawsey [ Sun Mar 20, 2011 7:20 am ]
Post subject:  Re: quick spotlight wiring question
I fitted a spotty to my zook a real old 1 thats been in the shed for 20 years or so,, 1 wire out straight to a switch on the dash via a fuse then to the battery. simple .probaly illegal and my car will catch on fire,but it works .earthed through the mounting bolt on the bumper
Author:  Rusho [ Sun Mar 20, 2011 7:31 am ]
Post subject:  Re: quick spotlight wiring question
dawsey wrote:
I fitted a spotty to my zook a real old 1 thats been in the shed for 20 years or so,, 1 wire out straight to a switch on the dash via a fuse then to the battery. simple .probaly illegal and my car will catch on fire,but it works .earthed through the mounting bolt on the bumper


I hope you only use your spotty for 10 minutes at a time. For the sake of $10-$15 get a relay and save yourself from a potential melt down :wink:
Author:  dawsey [ Sun Mar 20, 2011 7:34 am ]
Post subject:  Re: quick spotlight wiring question
I will..
Author:  sierra_1988 [ Mon Mar 21, 2011 12:20 pm ]
Post subject:  Re: quick spotlight wiring question
wired up spotties as per "good tech" forum advice. Harness installed as per instructions. Red wire from spotties on/off switch to right pin on one headlight (looking from engine compartment forward). Connected seperate earth from relay to left pin on light. Changed pos and neg (between spotties and harness)as per previous question. All to no avail - spotties not work :( . Will double check all issues over next couple of days/weeks and see whether I stuffed up somewhere.
Author:  MacDaddy [ Mon Mar 21, 2011 2:07 pm ]
Post subject:  Re: quick spotlight wiring question
whincup wrote:
stocker wrote:
if you have 2 wires coming out the back of the light then you should be 99% sure that its not connected to the metal chassis of the light on either.

And lights aren't Polarity sensitive seeing as they are just a Resistor that gets hot :)


what about HIDs? they the same?


Nope definitely not... HID's are not a normal " resistor " type bulb, they work more like a fluorescent tube/bulb, and the power supply they come with, could/maybe, be damaged by wiring it up with incorrect polarity... so best to right first time, and not guess... :D
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/