| auszookers.com http://auszookers.com/forum/ |
|
| Body lift for Sierra Qs http://auszookers.com/forum/viewtopic.php?f=5&t=22419 |
Page 1 of 1 |
| Author: | Bennyzarb [ Tue May 31, 2011 9:04 am ] |
| Post subject: | Body lift for Sierra Qs |
Hayy people I have a 92 Sierra with 31s extended shackles and 2in lifted ome springs I am after a 2 in body lift where can I get some should I make them and what do I need to do it Do I need to adjust steering arm or not |
|
| Author: | Gwagensteve [ Tue May 31, 2011 9:06 am ] |
| Post subject: | Re: Body lift for Sierra |
Just buy one from Just Cruzin: http://www.auszookers.com/index.php?nam ... ic&t=15518 You can't make one without a lathe - socket bolts have to be fabricated. Steve. |
|
| Author: | Bennyzarb [ Tue May 31, 2011 9:10 am ] |
| Post subject: | Re: Body lift for Sierra Qs |
Yea I am a panel beater and can get everything from work but not shaw if I should I am a bit lazy and I would just like to buy them and do the body lift at work will I need to make a steel spacer for the steering shaft |
|
| Author: | steak_knife [ Tue May 31, 2011 9:11 am ] |
| Post subject: | Re: Body lift for Sierra Qs |
Bennyzarb wrote: Yea I am a panel beater and can get everything from work but not shaw if I should I am a bit lazy and I would just like to buy them and do the body lift at work will I need to make a steel spacer for the steering shaft
Not with the kit from the link above, has a new thicker rag joint in it.. |
|
| Author: | Bennyzarb [ Tue May 31, 2011 9:14 am ] |
| Post subject: | Re: Body lift for Sierra Qs |
Ahh ok |
|
| Author: | Gwagensteve [ Tue May 31, 2011 9:14 am ] |
| Post subject: | Re: Body lift for Sierra Qs |
I've installed HEAPS of sierra BL's (used to make them when I had access to a lathe) and never needed a steering spacer at 2" BL. To clarify, Bennyzarb, you have to bore out and tap a thread into 16mm bolt creating a socket bolt. Just Cruzin's are very nicely made, and the cost of his kit is low enough that making the bolts yourself doesn't make any sense. Steve. |
|
| Author: | Bennyzarb [ Tue May 31, 2011 9:30 am ] |
| Post subject: | Re: Body lift for Sierra Qs |
Ahh ok I spoke to my local wrecker and they make body lifts for sierras and want $800 installed they said they make the blocks out of 50 mm steel and bend the shifter and put a longer steering shaft in out of an older Suzuki but the just cruzin one sounds better cause I get to keep $600 for some transfer gears  what do youse think of this body lift they make?
|
|
| Author: | steak_knife [ Tue May 31, 2011 9:34 am ] |
| Post subject: | Re: Body lift for Sierra Qs |
Bennyzarb wrote: Ahh ok I spoke to my local wrecker and they make body lifts for sierras and want $800 installed they said they make the blocks out of 50 mm steel and bend the shifter and put a longer steering shaft in out of an older Suzuki but the just cruzin one sounds better cause I get to keep $600 for some transfer gears
what do youse think of this body lift they make?I'm not a fan of body lift, but his are top shelf, if I had to lift I'd use his... |
|
| Author: | jimbo_jones [ Tue May 31, 2011 9:39 am ] |
| Post subject: | Re: Body lift for Sierra Qs |
Ive used Just Cruzin's body lift kit and can say its top knotch |
|
| Author: | Bennyzarb [ Tue May 31, 2011 9:39 am ] |
| Post subject: | Re: Body lift for Sierra Qs |
Ahh ok |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|