auszookers.com
http://auszookers.com/forum/

LJ80 gearbox bearing part numbers needed
http://auszookers.com/forum/viewtopic.php?f=5&t=25237		 Page 1 of 1
Author:  hooki [ Mon Aug 29, 2011 3:47 am ]
Post subject:  LJ80 gearbox bearing part numbers needed
:helloo:

does anyone have the part numbers for all the bearings and seals for a LJ80 4-speed gearbox?

thanks.
Author:  Fity [ Mon Aug 29, 2011 5:03 am ]
Post subject:  Re: LJ80 gearbox bearing part numbers needed
Are you after the Suzuki part numbers or the Bearing / seal number?
Author:  hooki [ Mon Aug 29, 2011 5:28 am ]
Post subject:  Re: LJ80 gearbox bearing part numbers needed
just the bearing/seal numbers please :)
Author:  Fity [ Mon Aug 29, 2011 5:42 am ]
Post subject:  Re: LJ80 gearbox bearing part numbers needed
Suzuki part number and their sizes/bearing numbers. 99% sure that this is correct. :)

09283-20028 Front oil seal 20x47x8.5
24780-79001 Rear oil seal 28x38x10x15
08113-62040 Bearings (you need 2) 6204C3
08163-62040 Bearing 20x47x14
08163-63040 Bearing 6304NC3
09263-17014 Needle Roller 17.5x22x15.8
Author:  hooki [ Mon Aug 29, 2011 5:43 am ]
Post subject:  Re: LJ80 gearbox bearing part numbers needed
awesome. Thanks Fity :D
Author:  Fity [ Mon Aug 29, 2011 6:24 am ]
Post subject:  Re: LJ80 gearbox bearing part numbers needed
I am not 100% sure if a LJ80-I and LJ80-II (Stockman) are the same, however I think they are both the same as a LJ50.
Author:  missmyljdaze [ Mon Aug 29, 2011 7:25 am ]
Post subject:  Re: LJ80 gearbox bearing part numbers needed
dont know if this is of any help,

but when my lj80 box dropped a heap of teeth, I just replaced everything with the cogs, seals and bearings from the spare lj50 box.

only difference was the bell housing being made for different bolt pattern motors.
internally they were identical.

stephen
Author:  303zuke [ Mon Aug 29, 2011 1:16 pm ]
Post subject:  Re: LJ80 gearbox bearing part numbers needed
Fity wrote:
Suzuki part number and their sizes/bearing numbers. 99% sure that this is correct. :)

09283-20028 Front oil seal 20x47x8.5
24780-79001 Rear oil seal 28x38x10x15
08113-62040 Bearings (you need 2) 6204C3
08163-62040 Bearing 20x47x14
08163-63040 Bearing 6304NC3
09263-17014 Needle Roller 17.5x22x15.8


LJ's get their awesomeness from the 4th dimension, Sierras just have a good spin circle ratio. :helloo:
Author:  Highway-Star [ Mon Aug 29, 2011 2:25 pm ]
Post subject:  Re: LJ80 gearbox bearing part numbers needed
Fity wrote:
I am not 100% sure if a LJ80-I and LJ80-II (Stockman) are the same, however I think they are both the same as a LJ50.


The only difference I've noticed between early and later LJ80 boxes is the later ones have a different aluminium casting for the shifter on top of the box. Seems the Stockman's scored some sort of the "sticky up bit" (yes thats a legit term) that the 80's and 50's dont have.



303zuke wrote:
Fity wrote:
Suzuki part number and their sizes/bearing numbers. 99% sure that this is correct. :)

09283-20028 Front oil seal 20x47x8.5
24780-79001 Rear oil seal 28x38x10x15
08113-62040 Bearings (you need 2) 6204C3
08163-62040 Bearing 20x47x14
08163-63040 Bearing 6304NC3
09263-17014 Needle Roller 17.5x22x15.8


LJ's get their awesomeness from the 4th dimension, Sierras just have a good spin circle ratio. :helloo:


:lol: :lol: :lol:

The 4th dimension is apparantly time...... so could be estimated life span of the seal?
Author:  Fity [ Tue Aug 30, 2011 1:58 am ]
Post subject:  Re: LJ80 gearbox bearing part numbers needed
303zuke wrote:
24780-79001 Rear oil seal 28x38x10x15


Looking at the seal it is 10mm wide at the mounting face and 15mm total width.
Author:  303zuke [ Tue Aug 30, 2011 1:29 pm ]
Post subject:  Re: LJ80 gearbox bearing part numbers needed
Try as you may to spoil it with facts, LJs are still full of awesomeness.
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/