ok i have a 4pin already
(well a pair of them)
where would i buy a solid spacer?
| auszookers.com http://auszookers.com/forum/ |
|
| Front diff upgrades http://auszookers.com/forum/viewtopic.php?f=5&t=25518 |
Page 1 of 1 |
| Author: | jonno_racing [ Tue Sep 06, 2011 1:10 pm ] |
| Post subject: | Front diff upgrades |
OK so i am building a W/T diff for the front of my coiler atm... specs are 3.9 c/p second hand, will set tolerances as tight as within spec will allow. wt flange powertrax locker Rock Assault 4340 Chromoly Axle Shafts vit calipers all new bearings i will laminate all arms housing has been shaved, trussed, crown wheel guard and knuckle gussets. is there anything else i should look at doing? i am wanting to run 34inch tires so lots of load on this one! and i would like to not have to touch him again other than usual maintenance possibly this http://www.lowrangeoffroad.com/index.ph ... t-kit.html not much to add on to the build.. i will also be doing a similar amour of work to the rear housing (w/t) so any ideas that way will help Phil |
|
| Author: | got_bar_work [ Tue Sep 06, 2011 7:22 pm ] |
| Post subject: | Re: Front diff upgrades |
If u upgrade them u might start breaking cromo cv |
|
| Author: | 31zook [ Tue Sep 06, 2011 7:27 pm ] |
| Post subject: | Re: Front diff upgrades |
Try a 4 pin front center, I know 3.9s usually come with them but I thought for everyone else it was worth mentioning... |
|
| Author: | shep [ Tue Sep 06, 2011 8:27 pm ] |
| Post subject: | Re: Front diff upgrades |
use a solid pinion spacer not the crush spacer. |
|
| Author: | jonno_racing [ Tue Sep 06, 2011 9:51 pm ] |
| Post subject: | Re: Front diff upgrades |
ok i have a 4pin already (well a pair of them)
where would i buy a solid spacer? |
|
| Author: | tanshi [ Tue Sep 06, 2011 10:50 pm ] |
| Post subject: | Re: Front diff upgrades |
jonno_racing wrote: ok i have a 4pin already
(well a pair of them)where would i buy a solid spacer? aparently one of the hilux ones can be used. there was a discussion on this a while back and it was decided that a solid spacer wasnt really needed |
|
| Author: | jonno_racing [ Wed Sep 07, 2011 6:22 am ] |
| Post subject: | Re: Front diff upgrades |
is it worth going to grade 12 shcs bolts on king pins? |
|
| Author: | ajsr [ Wed Sep 07, 2011 7:37 am ] |
| Post subject: | Re: Front diff upgrades |
I dont think you need half of the crap in your original post to run 34's , just cromos and locker |
|
| Author: | SierraDan [ Wed Sep 07, 2011 7:38 am ] |
| Post subject: | Re: Front diff upgrades |
What about 35's? |
|
| Author: | jonno_racing [ Wed Sep 07, 2011 7:41 am ] |
| Post subject: | Re: Front diff upgrades |
ajsr wrote: I dont think you need half of the crap in your original post to run 34's , just cromos and locker
your probably right.. but cant hurt to beef it up a bit more than required. i also want to run a front dig. |
|
| Author: | SierraDan [ Wed Sep 07, 2011 7:49 am ] |
| Post subject: | Re: Front diff upgrades |
jonno_racing wrote: ajsr wrote: I dont think you need half of the crap in your original post to run 34's , just cromos and locker your probably right.. but cant hurt to beef it up a bit more than required. i also want to run a front dig. Isnt front dig when you have rear disconnect and a line locker? |
|
| Author: | dank [ Wed Sep 07, 2011 7:57 am ] |
| Post subject: | Re: Front diff upgrades |
make sure you set the castor properly for your ride height and go back to stock suzuki rubber bushes if you've been using castor correction bushes. |
|
| Author: | jonno_racing [ Wed Sep 07, 2011 7:57 am ] |
| Post subject: | Re: Front diff upgrades |
SierraDan wrote: jonno_racing wrote: ajsr wrote: I dont think you need half of the crap in your original post to run 34's , just cromos and locker your probably right.. but cant hurt to beef it up a bit more than required. i also want to run a front dig. Isnt front dig when you have rear disconnect and a line locker?  prob wont go line locker, will just get handbrake working spot on.
|
|
| Author: | jonno_racing [ Wed Sep 07, 2011 7:59 am ] |
| Post subject: | Re: Front diff upgrades |
dank wrote: make sure you set the castor properly for your ride height and go back to stock suzuki rubber bushes if you've been using castor correction bushes.
yeah dank thats all under control. i will be setting the caster to 4degrees at ride height with standard arms... i will be making high clearance tube arms but with the option of using a stock arm if the situation calls for it. |
|
| Author: | ajsr [ Wed Sep 07, 2011 8:03 am ] |
| Post subject: | Re: Front diff upgrades |
jonno_racing wrote: dank wrote: make sure you set the castor properly for your ride height and go back to stock suzuki rubber bushes if you've been using castor correction bushes. yeah dank thats all under control. i will be setting the caster to 4degrees at ride height with standard arms... i will be making high clearance tube arms but with the option of using a stock arm if the situation calls for it. you should just put leaves in and all will work 
|
|
| Author: | jimny_timmy [ Wed Sep 07, 2011 8:10 am ] |
| Post subject: | Re: Front diff upgrades |
ajsr wrote: jonno_racing wrote: dank wrote: make sure you set the castor properly for your ride height and go back to stock suzuki rubber bushes if you've been using castor correction bushes. yeah dank thats all under control. i will be setting the caster to 4degrees at ride height with standard arms... i will be making high clearance tube arms but with the option of using a stock arm if the situation calls for it. you should just put leaves in and all will work Hahahahahahaha |
|
| Author: | jonno_racing [ Wed Sep 07, 2011 8:12 am ] |
| Post subject: | Re: Front diff upgrades |
ajsr wrote: jonno_racing wrote: dank wrote: make sure you set the castor properly for your ride height and go back to stock suzuki rubber bushes if you've been using castor correction bushes. yeah dank thats all under control. i will be setting the caster to 4degrees at ride height with standard arms... i will be making high clearance tube arms but with the option of using a stock arm if the situation calls for it. you should just put leaves in and all will work and be just like you? nah.. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|