bristlenose2008 wrote:
steak_knife wrote:
That's a pressure sender , just change the connector on the wire, no problem...
where do I get a connector like that?
it uses the same connector, flat spade female slips over it
| auszookers.com http://auszookers.com/forum/ |
|
| Oil Temp sensor Query/Problem http://auszookers.com/forum/viewtopic.php?f=5&t=25703 |
Page 1 of 1 |
| Author: | bristlenose2008 [ Sun Sep 11, 2011 11:17 am ] |
| Post subject: | Oil Temp sensor Query/Problem |
In my last parts order for an engine build a non genuine part was chosen. Sadly I must say....as the part is somewhat different. What should I do, return it, or is this the replacement part for a possibly discontinued part? Please comment if you have recent knowledge. |
|
| Author: | bristlenose2008 [ Sun Sep 11, 2011 11:25 am ] |
| Post subject: | where it goes |
this is where it goes for anyone curious right above the oil filter |
|
| Author: | steak_knife [ Sun Sep 11, 2011 11:26 am ] |
| Post subject: | Re: Oil Temp sensor Query/Problem |
That's a pressure sender , just change the connector on the wire, no problem... |
|
| Author: | bristlenose2008 [ Sun Sep 11, 2011 11:34 am ] |
| Post subject: | Re: where it goes |
bristlenose2008 wrote: this is where it goes for anyone curious right above the oil filter
|
|
| Author: | bristlenose2008 [ Sun Sep 11, 2011 11:34 am ] |
| Post subject: | Re: Oil Temp sensor Query/Problem |
steak_knife wrote: That's a pressure sender , just change the connector on the wire, no problem...
where do I get a connector like that? |
|
| Author: | joe5701 [ Sun Sep 11, 2011 8:42 pm ] |
| Post subject: | Re: Oil Temp sensor Query/Problem |
bristlenose2008 wrote: steak_knife wrote: That's a pressure sender , just change the connector on the wire, no problem... where do I get a connector like that? it uses the same connector, flat spade female slips over it
|
|
| Author: | bristlenose2008 [ Tue Sep 13, 2011 11:25 am ] |
| Post subject: | Re: Oil Temp sensor Query/Problem |
joe5701 wrote: bristlenose2008 wrote: steak_knife wrote: That's a pressure sender , just change the connector on the wire, no problem... where do I get a connector like that? it uses the same connector, flat spade female slips over it been to Dick Smith, no connectors like this. Would Jaycar have it or am I looking in the wrong places? |
|
| Author: | joe5701 [ Tue Sep 13, 2011 11:33 am ] |
| Post subject: | Re: Oil Temp sensor Query/Problem |
bristlenose2008 wrote: joe5701 wrote: bristlenose2008 wrote: steak_knife wrote: That's a pressure sender , just change the connector on the wire, no problem... where do I get a connector like that? it uses the same connector, flat spade female slips over it been to Dick Smith, no connectors like this. Would Jaycar have it or am I looking in the wrong places? use the same connector as the old switch http://www.google.com.au/imgres?q=femal ... 2CQ&zoom=1 it slides over the round end |
|
| Author: | joe5701 [ Tue Sep 13, 2011 11:56 am ] |
| Post subject: | Re: Oil Temp sensor Query/Problem |
http://www.google.com.au/imgres?q=femal ... OCg&zoom=1 |
|
| Author: | Reubs [ Tue Sep 13, 2011 10:41 pm ] |
| Post subject: | Re: Oil Temp sensor Query/Problem |
Is there any benefit to be gained from replacing an oil pressure sender? I doubt the OE sender would ever fail in maybe 1,000,000km |
|
| Author: | royce [ Tue Sep 13, 2011 10:51 pm ] |
| Post subject: | Re: Oil Temp sensor Query/Problem |
Ill assume thats not a pic of your engine cause the head is olf and the oil filter looks to cost about 50c but yeah this type of terminal jsut pushes onto it 
Reubs, oil pressure switches fail quite a bit, either switching too low or high or not at all |
|
| Author: | Reubs [ Wed Sep 14, 2011 1:12 am ] |
| Post subject: | Re: Oil Temp sensor Query/Problem |
royce wrote: Reubs, oil pressure switches fail quite a bit, either switching too low or high or not at all
Okay - thanks for that insight - just never personally seen one fail. |
|
| Author: | bristlenose2008 [ Sun Sep 25, 2011 1:12 am ] |
| Post subject: | Re: Oil Temp sensor Query/Problem |
royce wrote: Ill assume thats not a pic of your engine cause the head is olf and the oil filter looks to cost about 50c
but yeah this type of terminal jsut pushes onto it Reubs, oil pressure switches fail quite a bit, either switching too low or high or not at all aha, thanks! Now I get how they connect. The engine on that picture was my engine, but that was the 1st or 2nd block. I am up to the 4th block now, but it should look the same. The oil filter on there was one that got delivered to me before the rebuild process began. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|