| auszookers.com http://auszookers.com/forum/ |
|
| locker trouble http://auszookers.com/forum/viewtopic.php?f=5&t=27331 |
Page 1 of 2 |
| Author: | scrubby [ Wed Nov 02, 2011 6:21 am ] |
| Post subject: | locker trouble |
trying to fit this to the front ofmy 90 model tin top wt http://www.ebay.com.au/itm/DIFF-LOCK-SP ... 0650491618 i dont have the 3 pin part and the square bit with the 4 spider gears are they.. have i got the wrong locker excuse the laymans terms mine is just 1 pin with 2 spider gears  says it fits any 1.3 leaf sprung sierra
|
|
| Author: | neofitou [ Wed Nov 02, 2011 6:54 am ] |
| Post subject: | Re: locker trouble |
Put up some pics! Sounds like you've got an unusual diff there, I think the vitara ones are like that, Christover managed to get his together if this is the case as he put the Spartan in the front of his vit. Also, you got jacked if you paid that price. http://www.lowrangeoffroad.com/index.ph ... uzsam.html. I had the Spartan front and rear in my Sierra. |
|
| Author: | abclarke [ Wed Nov 02, 2011 6:55 am ] |
| Post subject: | Re: locker trouble |
Yeha man i saw this one on ebay and then i just checked low range, even with delivery its like $100 less still 
|
|
| Author: | SierraDan [ Wed Nov 02, 2011 7:29 am ] |
| Post subject: | Re: locker trouble |
Your front diff is the two pin. So you will need a 4pin and put it up front. But you should be sweet to use it with the two pin centre if you can find a pin block to hold the washers in place. Or just put it in the rear. I have the same locker in the rear and it's awesome. |
|
| Author: | Built4thrashing [ Wed Nov 02, 2011 7:33 am ] |
| Post subject: | Re: locker trouble |
they were right. It will fit in any1.3ltr leaf sprung sierra diff. it will even work in a single pin diff but you need the cross pin block to hold the side gears apart. I know a few sierras that run a lockright in the same diff as yours.... |
|
| Author: | scrubby [ Wed Nov 02, 2011 7:36 am ] |
| Post subject: | Re: locker trouble |
ok so the (2 pin) is that just one pin straight through? cause that is what is in there! so i need a new diff center? would be alot stronger with the right diff yeah? |
|
| Author: | SierraDan [ Wed Nov 02, 2011 7:38 am ] |
| Post subject: | Re: locker trouble |
That's the 2pin yes. You can get a 4pin centre. Or get a pin block from a 4pin centre and it will work. |
|
| Author: | scrubby [ Wed Nov 02, 2011 7:48 am ] |
| Post subject: | Re: locker trouble |
so would it be weaker with the 2 pin? an you wouldn happen to know where i might source one of those blocks? an is this a sierra diff center or somethin else?
|
|
| Author: | SierraDan [ Wed Nov 02, 2011 8:00 am ] |
| Post subject: | Re: locker trouble |
Yes, but I wouldn't worry about it. You'd break a CV before the centre I'd say. I think shep has a 2pin locked front. You could get it from a 4pin diff. So any rear diff and older fronts. But if you're looking for a centre to get the pin, you might as well use the whole thing. Depending on when you need it I could pull a diff apart and send it to you. But I don't have much time till after the weekend. |
|
| Author: | scrubby [ Wed Nov 02, 2011 8:05 am ] |
| Post subject: | Re: locker trouble |
ok so do you think the back is the same or would it be the 4 pin? so you got one for sale dan? no rush might just put it back together do another day! |
|
| Author: | SierraDan [ Wed Nov 02, 2011 8:12 am ] |
| Post subject: | Re: locker trouble |
The rear is a 4pin and will go straight in. I have the same locker in the rear of mine. I can send you a pin block next week if you need it. |
|
| Author: | scrubby [ Wed Nov 02, 2011 8:21 am ] |
| Post subject: | Re: locker trouble |
yeah well im going to need one by the looks |
|
| Author: | also76 [ Wed Nov 02, 2011 8:52 am ] |
| Post subject: | Re: locker trouble |
yeah had this same convo with shep, he is running a 2pin diff with a lockrite locker. oi dan, how many of those pin blocks you got ? ill take one aswell if you got it ? what sort of price ya after ? |
|
| Author: | SierraDan [ Wed Nov 02, 2011 8:56 am ] |
| Post subject: | Re: locker trouble |
Only one left I'm willing to part with I'm pretty sure mate. Sorry. |
|
| Author: | scrubby [ Tue Nov 08, 2011 4:29 am ] |
| Post subject: | Re: locker trouble |
ok so ive fitted the spartan locker to the front diff into the 2 pin carrier and just used the square block out of a rear diff that had a 4 pin carrier but when you lock the hubs and try to turn left it just clunks and it does the same thing to the right but only just turns to the right..
|
|
| Author: | christover1 [ Tue Nov 08, 2011 6:18 am ] |
| Post subject: | Re: locker trouble |
I'd give it time to bed in, should free up. Mine was like that at first. Did you make sure that you removed the thrust washers, as they can hide in the grease and crud. If they still in there, locker can't unlock. |
|
| Author: | SierraDan [ Tue Nov 08, 2011 6:25 am ] |
| Post subject: | Re: locker trouble |
Why didn't you use the 4pin carrier? |
|
| Author: | christover1 [ Tue Nov 08, 2011 6:25 am ] |
| Post subject: | Re: locker trouble |
PS. Some people have had to trim down the pin block, to get locker to work, is rare, but can happen. To unluck properly, there needs to be enough space for locker to slide away from side gear, Hence need to make sure original thrust washers are not stuck to the gears or centre. And why some have needed to trim down the block. |
|
| Author: | christover1 [ Tue Nov 08, 2011 6:26 am ] |
| Post subject: | Re: locker trouble |
SierraDan wrote: Why didn't you use the 4pin carrier?
Methinks he only got the pin block, not an entire diff ?? |
|
| Author: | steak_knife [ Tue Nov 08, 2011 6:31 am ] |
| Post subject: | Re: locker trouble |
christover1 wrote: PS. Some people have had to trim down the pin block,
to get locker to work, is rare, but can happen. To unluck properly, there needs to be enough space for locker to slide away from side gear, Hence need to make sure original thrust washers are not stuck to the gears or centre. And why some have needed to trim down the block. I still run the thrust washer's & linished the block, work's perfect..... 
|
|
| Author: | Scrawny [ Tue Nov 08, 2011 6:39 am ] |
| Post subject: | Re: locker trouble |
I just give it to the X-Spurts, so much easier! |
|
| Author: | steak_knife [ Tue Nov 08, 2011 6:43 am ] |
| Post subject: | Re: locker trouble |
Scrawn wrote: I just give it to the X-Spurts, so much easier!
you paid for something??? 
|
|
| Author: | Scrawny [ Tue Nov 08, 2011 6:47 am ] |
| Post subject: | Re: locker trouble |
steak_knife wrote: Scrawn wrote: I just give it to the X-Spurts, so much easier! you paid for something??? 
 It's not what you know, it's who 
|
|
| Author: | scrubby [ Tue Nov 08, 2011 7:10 am ] |
| Post subject: | Re: locker trouble |
yeah removed thrust washer and didnt use the 4 pin cause it was out of the rear think it said sj50 said on the diff center and front axles was to small for it.. |
|
| Author: | scrubby [ Tue Nov 08, 2011 8:27 am ] |
| Post subject: | Re: locker trouble |
christover1 wrote: I'd give it time to bed in, should free up.
Mine was like that at first. Did you make sure that you removed the thrust washers, as they can hide in the grease and crud. If they still in there, locker can't unlock. yeah removed them.. and did yours not let you turn right at all cause thats what mine is doing
|
|
| Author: | scrubby [ Tue Nov 08, 2011 8:32 am ] |
| Post subject: | Re: locker trouble |
SierraDan wrote: Why didn't you use the 4pin carrier?
it was out of a rear diff center and the side gears was to big for the axle and the side gears out of the 2 pin wouldn fit in cause they were to big.. grr 
|
|
| Author: | scrubby [ Tue Nov 08, 2011 8:34 am ] |
| Post subject: | Re: locker trouble |
christover1 wrote: PS. Some people have had to trim down the pin block,
to get locker to work, is rare, but can happen. To unluck properly, there needs to be enough space for locker to slide away from side gear, Hence need to make sure original thrust washers are not stuck to the gears or centre. And why some have needed to trim down the block. ok i'll have to pull it out and see whats going on in there.. |
|
| Author: | christover1 [ Tue Nov 08, 2011 8:35 am ] |
| Post subject: | Re: locker trouble |
Occassionally it would not let me steer, usually during 3 point type turns. A quick left right on steering usually freed it up. Doesn't do it now. I remember during my instal, 1 of the tiny pins was a bit tight, think that was my cause. You either have to give it time, or pull it out and double check everything. Whatever you feel is right. If you pull it out, make sure locker has enough room to unlock, |
|
| Author: | christover1 [ Tue Nov 08, 2011 8:39 am ] |
| Post subject: | Re: locker trouble |
|
|
| Author: | scrubby [ Tue Nov 08, 2011 8:43 am ] |
| Post subject: | Re: locker trouble |
christover1 wrote: Occassionally it would not let me steer,
usually during 3 point type turns. A quick left right on steering usually freed it up. Doesn't do it now. I remember during my instal, 1 of the tiny pins was a bit tight, think that was my cause. You either have to give it time, or pull it out and double check everything. Whatever you feel is right. If you pull it out, make sure locker has enough room to unlock, ok well i can turn the left fine but it make a really bad crunchin clunkin noise then when you go to turn it back its really hard and wont even really turn to the right.. might just pull apart and have another look how do i know if its got room to unlock? |
|
| Page 1 of 2 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|