| auszookers.com http://auszookers.com/forum/ |
|
| Wiring up trailer point on a jimny http://auszookers.com/forum/viewtopic.php?f=5&t=28126 |
Page 1 of 1 |
| Author: | jimny06 [ Mon Nov 28, 2011 9:56 am ] |
| Post subject: | Wiring up trailer point on a jimny |
Hey guys my jimnys got a tow bar but no point to plug in for the lights. I was going to tap into the tail lights to run the cable but saw something on google about an adapter clip you can buy and plug in somewhere. Any ideas on the easiest way to do this? |
|
| Author: | stewy91 [ Mon Nov 28, 2011 10:15 am ] |
| Post subject: | Re: Wiring up trailer point on a jimny |
I assume this is what you are talking about http://www.narva.com.au/products/browse ... swire-taps |
|
| Author: | Jester [ Mon Nov 28, 2011 7:01 pm ] |
| Post subject: | Re: Wiring up trailer point on a jimny |
i believe hes meaning a plug n play loom, which is available on many larger 4x4s but i really have no idea for a jimny, but those wire taps are evil |
|
| Author: | JayKay [ Mon Nov 28, 2011 7:07 pm ] |
| Post subject: | Re: Wiring up trailer point on a jimny |
On my Jimny, the wiring loom runs up behind the right rear tail light. You unplug the plug behind the brake light and plug in the loom between that and the existing plug. If that makes sense ? |
|
| Author: | 89_tintop [ Mon Nov 28, 2011 9:26 pm ] |
| Post subject: | Re: Wiring up trailer point on a jimny |
What part of brissie you in? |
|
| Author: | alien [ Mon Nov 28, 2011 9:35 pm ] |
| Post subject: | Re: Wiring up trailer point on a jimny |
try www.parksidetowbars.com.au - they have "wire safe" looms - not sure about jimny but you might get lucky. |
|
| Author: | jimny06 [ Tue Nov 29, 2011 1:23 am ] |
| Post subject: | Re: Wiring up trailer point on a jimny |
I'm in Albany creek in brissy. Yeah was basically after a plug and go loom to avoid tapping in. Hopefully I can get one to adapt onto somewhere near the tail lights? Thanks for the websites guys I'll check them out |
|
| Author: | jimny06 [ Sat Dec 03, 2011 2:39 pm ] |
| Post subject: | Re: Wiring up trailer point on a jimny |
No one else knows of any plug and play trailer looms? |
|
| Author: | steak_knife [ Sat Dec 03, 2011 6:36 pm ] |
| Post subject: | Re: Wiring up trailer point on a jimny |
jimny06 wrote: No one else knows of any plug and play trailer looms?
Suzuki make em, but......... $$$$$'s...... Could be worth a look, may not be to much... |
|
| Author: | 89_tintop [ Sat Dec 03, 2011 11:36 pm ] |
| Post subject: | Re: Wiring up trailer point on a jimny |
why not just tap into the original loom .. why do you want a plug in set up or come to me and i will do it for you.. easy as and will save you some $$$.. cost you about $30 tops on parts.. |
|
| Author: | jimny06 [ Sun Dec 04, 2011 7:51 am ] |
| Post subject: | Re: Wiring up trailer point on a jimny |
Yeah I am planning on tapping into it but though if there was a plug and play it would be a big easier. I suppose I'll just cut the wires and solder some new ones on for the trailer no big deal. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|