BlueSuzy wrote:
Meh, Even a steel wire brush is fine on threads. Do it all the time to clean the loctite out of them.
Haha stainless wheel on thin plate didnt work too well for me
| auszookers.com http://auszookers.com/forum/ |
|
| wire brush http://auszookers.com/forum/viewtopic.php?f=5&t=28189 |
Page 1 of 1 |
| Author: | koozers [ Thu Dec 01, 2011 12:13 am ] |
| Post subject: | wire brush |
Stoopid ? time Will a wire brush (on a drill) stuff up the thread on a bolt? |
|
| Author: | BlueSuzy [ Thu Dec 01, 2011 12:18 am ] |
| Post subject: | Re: wire brush |
no. I use a wire brush all the time on the bench grinder at work. Makes things shiney and new again. |
|
| Author: | abclarke [ Thu Dec 01, 2011 12:40 am ] |
| Post subject: | Re: wire brush |
As long as what ever the wire brush is made out of is weaker than the thing your buffing it'll be all good! |
|
| Author: | koozers [ Thu Dec 01, 2011 12:49 am ] |
| Post subject: | Re: wire brush |
umm ok Brass plated steel brush vs Wheel Stud Whos ur money on ???? |
|
| Author: | BlueSuzy [ Thu Dec 01, 2011 1:13 am ] |
| Post subject: | Re: wire brush |
Meh, Even a steel wire brush is fine on threads. Do it all the time to clean the loctite out of them. |
|
| Author: | koozers [ Thu Dec 01, 2011 1:27 am ] |
| Post subject: | Re: wire brush |
thankee muchlee |
|
| Author: | abclarke [ Thu Dec 01, 2011 4:55 am ] |
| Post subject: | Re: wire brush |
BlueSuzy wrote: Meh, Even a steel wire brush is fine on threads. Do it all the time to clean the loctite out of them.
Haha stainless wheel on thin plate didnt work too well for me
|
|
| Author: | buzbox [ Thu Dec 01, 2011 5:47 am ] |
| Post subject: | Re: wire brush |
a knotted wire brush may fk things up though |
|
| Author: | BlueSuzy [ Thu Dec 01, 2011 6:30 am ] |
| Post subject: | Re: wire brush |
well yeah, i guess the thickness/grade depends.. Your not going to brush your teeth with a scrubbing brush..to coarse. |
|
| Author: | koozers [ Thu Dec 01, 2011 7:30 am ] |
| Post subject: | Re: wire brush |
more questions |
|
| Author: | Scrawny [ Thu Dec 01, 2011 7:38 am ] |
| Post subject: | Re: wire brush |
Looks like it |
|
| Author: | steak_knife [ Thu Dec 01, 2011 7:38 am ] |
| Post subject: | Re: wire brush |
Yes, don't get to much heat in it & strip the brake's out before welding... |
|
| Author: | koozers [ Thu Dec 01, 2011 8:21 am ] |
| Post subject: | Re: wire brush |
taa |
|
| Author: | want33s [ Thu Dec 01, 2011 8:50 am ] |
| Post subject: | Re: wire brush |
steak_knife wrote: Yes, don't get to much heat in it & strip the brake's out before welding...
What is this welding you speak of? Is that like your gluing?  
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|