| auszookers.com http://auszookers.com/forum/ |
|
| a little help please http://auszookers.com/forum/viewtopic.php?f=5&t=2875 |
Page 1 of 1 |
| Author: | BIG_little [ Tue Sep 02, 2008 9:57 pm ] |
| Post subject: | a little help please |
can any one help me out with my transfer case i have a set of stage 3 reduction gears to put in but need to replace the needle rollers an bearings on box, thrust washers and replace all ceals where can i go besides suzuki sports for my needs ? cheers. |
|
| Author: | Damo [ Tue Sep 02, 2008 10:16 pm ] |
| Post subject: | Re: a little help please |
BIG_little wrote: can any one help me out with my transfer case i have a set of stage 3 reduction gears to put in but need to replace the needle rollers an bearings on box, thrust washers and replace all ceals where can i go besides suzuki sports for my needs ? cheers.
Check your counter shaft, it'll probably need replacing too. |
|
| Author: | BIG_little [ Wed Sep 03, 2008 12:51 am ] |
| Post subject: | Re: a little help please |
by the sounds of that i best just re build it cheers. |
|
| Author: | Damo [ Wed Sep 03, 2008 2:45 am ] |
| Post subject: | Re: a little help please |
BIG_little wrote: by the sounds of that i best just re build it cheers.
If you are putting some $$$ gears into it then it's a good idea. |
|
| Author: | Rockhopper [ Wed Sep 03, 2008 11:15 am ] |
| Post subject: | Re: a little help please |
http://www.locktup4x4.com.au/ in Australia http://www.lowrangeoffroad.com/ in the States |
|
| Author: | BIG_little [ Wed Sep 03, 2008 9:04 pm ] |
| Post subject: | Re: a little help please |
i checked out locktup an the transfer case re build kit doesnt show the needle rollers only the ball bearing type, i have needle rollers in mine? |
|
| Author: | mrw82 [ Wed Sep 03, 2008 10:21 pm ] |
| Post subject: | Re: a little help please |
cbc, bsc etc.... any bearing shop will be able to supply you with what you need I rebuild mine recently and made note of the part numbers these are BSC part numbers but most places should be able to workout what you need. 62/28C3 ball bearing x3 63/22C3 ball bearing x1 6306NRC3 ball bearing x1 TC12545 oil seal x2 TC12539 oil seal x1 (this seal may be different if you have a case without the handbrake attached to it, I can confirm in a few weeks) this doesn't include the needle roller bearings but the bearing shops should be able to supply them if you give them a sample. this all cost $113.90 trade price. well worth it when you consider the cost of the gears they are supporting. oh yeah, dont forget to set the shaft endfloat/bearing preload when you rebuild the case. I got the case gaskets from suzisport for $9.00 for the pair cheers, Mark. |
|
| Author: | Damo [ Wed Sep 03, 2008 10:33 pm ] |
| Post subject: | Re: a little help please |
mrw82 wrote: oh yeah, dont forget to set the shaft endfloat/bearing preload when you rebuild the case.
Part numbers for the shims are in my part numbers post in the tech section. You'll have to order these from Suzuki, though Suzisport etc could order them for you I think. |
|
| Author: | mrw82 [ Wed Sep 03, 2008 11:17 pm ] |
| Post subject: | Re: a little help please |
buy some shim material from the bearing shop and cut them out yourself. or as was suggested to me the other day cut up a coke can to use. |
|
| Author: | BIG_little [ Fri Sep 05, 2008 12:40 am ] |
| Post subject: | Re: a little help please |
cheers for all your help |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|