auszookers.com
http://auszookers.com/forum/

Differences between g16a and g16b ?
http://auszookers.com/forum/viewtopic.php?f=5&t=29235		 Page 1 of 1
Author:  g16b [ Tue Jan 03, 2012 11:26 pm ]
Post subject:  Differences between g16a and g16b ?
Have been searching for info re the 16a and 16b. I thought 16a was carby fed and 16b was efi. Alas I found a g16a engine with efi :?

Simply put, what are the differences ?

The 16a I got came out of a vitara and from all appearances is near exact on the outside, I did find the efi throttle body intake different (one has a longer throat) and different pellet senser body ( if that makes sense ).

Can the 16a being efi go into my vitara whilst I rebuild my 16b ?

All the googling has confused me even more hence the post.

Regards, chris.
Author:  buzbox [ Tue Jan 03, 2012 11:33 pm ]
Post subject:  Re: differnce between g16a and g16b
G16A = carby = SWB Vit
G16B = EFI = LWB Vit

G16a EFI = I think it may be an 8 Valve instead of G16B 16V (I could be wrong)

Personally I think putting the G16a EFI will be like putting in a V6 to replace a V8, not so much as in power wise but downgrading in engine. You might as well wait until the B is ready to be reinstalled, less dicking around, headaches etc.
Author:  Daves4wd [ Tue Jan 03, 2012 11:41 pm ]
Post subject:  Re: differnce between g16a and g16b
Could you put the injection manifold on the 16a of the 16b?? If so why not run that if it's a daily
Author:  89_tintop [ Tue Jan 03, 2012 11:46 pm ]
Post subject:  Re: differnce between g16a and g16b
buzbox wrote:
G16A = carby = SWB Vit
G16B = EFI = LWB Vit

G16a EFI = I think it may be an 8 Valve instead of G16B 16V (I could be wrong)

Personally I think putting the G16a EFI will be like putting in a V6 to replace a V8, not so much as in power wise but downgrading in engine. You might as well wait until the B is ready to be reinstalled, less dicking around, headaches etc.


close

G16b also came out swb vits in the later models

the japanese also used a g16a with the 16valve efi head.

if it is a 16 valve one just swap your inlet manifold onto the engine and any other sensors and slot it in.
Author:  g16b [ Wed Jan 04, 2012 12:09 am ]
Post subject:  Re: differnce between g16a and g16b
ahhh so it may be an import as it has 16 valves...just pulled the head off and the 16b pistons are the same size...hmmm

velly velly confusing...

would it be possible to interchange parts between the engines ?

I think I read somewhere that the 16a in NZ were 16valve, efi...just wondering where this engine come from, NZ..Japan...who knows !
Author:  christover1 [ Wed Jan 04, 2012 2:29 am ]
Post subject:  Re: differnce between g16a and g16b
The import engine I just fitted to my Vit,
is a G16A 16 valve efi
Author:  Scrawny [ Wed Jan 04, 2012 3:35 am ]
Post subject:  Re: differnce between g16a and g16b
There are internal differences too. From memory the 16b has a braced crankshaft
Author:  christover1 [ Wed Jan 04, 2012 3:39 am ]
Post subject:  Re: differnce between g16a and g16b
Scrawn wrote:
There are internal differences too. From memory the 16b has a braced crankshaft

My original B did, I fitted it to the import, along with vit sump and oil pick up
Author:  oohsam [ Thu Feb 14, 2013 2:00 pm ]
Post subject:  Re: differnce between g16a and g16b
i've got a local G16a efi 16 valve in my 95 vitara.

Go figure!
Author:  Fatzook [ Thu Feb 14, 2013 3:49 pm ]
Post subject:  Re: differnce between g16a and g16b
oohsam wrote:
i've got a local G16a efi 16 valve in my 95 vitara.

Go figure!



Good chance its a replacement motor then.
Author:  oohsam [ Thu Feb 14, 2013 3:54 pm ]
Post subject:  Re: differnce between g16a and g16b
Nah its original i have the original papers !
Author:  christover1 [ Thu Feb 14, 2013 3:55 pm ]
Post subject:  Re: differnce between g16a and g16b
May explain the odd looking front diff carrier
Author:  oohsam [ Thu Feb 14, 2013 3:56 pm ]
Post subject:  Re: differnce between g16a and g16b
Its build date is 95 but sold and regd as a 96
Author:  oohsam [ Thu Feb 14, 2013 3:57 pm ]
Post subject:  Re: differnce between g16a and g16b
Nah that diff carrier is out of a different vit
Author:  droverdave [ Thu Feb 14, 2013 4:06 pm ]
Post subject:  Re: differnce between g16a and g16b
http://www.teamswift.net/viewtopic.php?f=7&t=1904

That thread suggestes changes from single point to multi point injection through to cast iron vs aluminum blocks.

http://www.teamswift.net/viewtopic.php? ... 3&start=25

second post in this one seems to offer some good (but unverifiable) information.
Author:  Parry [ Thu Feb 14, 2013 6:34 pm ]
Post subject:  Re: differnce between g16a and g16b
I have a g16a efi, didn't know it was an a till I got it home, I thought I'd been ripped till I did some searching!
Author:  fordem [ Fri Feb 15, 2013 5:13 am ]
Post subject:  Re: differnce between g16a and g16b
droverdave wrote:
That thread suggestes changes from single point to multi point injection through to cast iron vs aluminum blocks.


That thread is like this one - nothing verifiable, just a bunch of opinions and FWIW here's mine - Suzuki never made an engine with a cast iron block.
Author:  royce [ Fri Feb 15, 2013 5:55 am ]
Post subject:  Re: differnce between g16a and g16b
I am sure we covered this before and losfer listed all the differences

what it doesn't point to is any difference in the stuff hung off the outside and what head it has, its just the A was made first and it might be something like a different crank girdle setup and slightly different crank, cant remember
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/