scraper is the only way unless you want to use some really badass chemicals...
http://www.selleys.com.au/sealants/silicone/remover
| auszookers.com http://auszookers.com/forum/ |
|
| Getting silicon off http://auszookers.com/forum/viewtopic.php?f=5&t=29351 |
Page 1 of 1 |
| Author: | Che [ Sat Jan 07, 2012 8:36 am ] |
| Post subject: | Getting silicon off |
Hi guys. What's the best way to get silicon off? A previous owner has gone a bit crazy with the stuff along a couple of seams, but want to get it all off so I can lay a bit of paint down |
|
| Author: | shep [ Sat Jan 07, 2012 8:50 am ] |
| Post subject: | Re: Getting silicon off |
use hammertone paint. problem solved |
|
| Author: | alien [ Sat Jan 07, 2012 8:52 am ] |
| Post subject: | Re: Getting silicon off |
scraper is the only way unless you want to use some really badass chemicals...
http://www.selleys.com.au/sealants/silicone/remover |
|
| Author: | atari4x4 [ Sat Jan 07, 2012 9:07 am ] |
| Post subject: | Re: Getting silicon off |
shep wrote: use hammertone paint.
problem solved fish eyes in a can, spray painters worst nightmare 
i'm no painter but, i'd clean it up as much as possible, prep the area, wash it with prepsol/wax n grease remover & hope for the best or go back to bare metal. pretty sure there is a silicone type additive that you can get for contaminated cars that you mix with the paint to stop the paint reacting with the silicone when spraying with a gun/compressor. paging ajsr... 
|
|
| Author: | TheOtherLeft [ Sat Jan 07, 2012 9:27 am ] |
| Post subject: | Re: Getting silicon off |
Not sure about Silicon, but I use Eucalyptus oil cleaning up Sikaflex. Works brilliantly. |
|
| Author: | ajsr [ Sat Jan 07, 2012 10:03 am ] |
| Post subject: | Re: Getting silicon off |
atari4x4 wrote: shep wrote: use hammertone paint. problem solved fish eyes in a can, spray painters worst nightmare i'm no painter but, i'd clean it up as much as possible, prep the area, wash it with prepsol/wax n grease remover & hope for the best or go back to bare metal. pretty sure there is a silicone type additive that you can get for contaminated cars that you mix with the paint to stop the paint reacting with the silicone when spraying with a gun/compressor. paging ajsr... plastic scraper (if you dont want to scratch shit) other wise steel is better and then prepsol and your fingernail. sometimes those pinstripe removal wheels work well to silicone sucks balls and is for lazy fuckers oh and for painting silicone drops stops fish eyes. |
|
| Author: | TZAR [ Sat Jan 07, 2012 10:07 am ] |
| Post subject: | Re: Getting silicon off |
high powered gerni sand blaster soda blaster Petrol Acid That selleys stuff is basically petrol/acid mix in a gel I am a tight arse so I would use my fingers as much as I can then rub with petrol, getting a terrible headache, then finish with acetone for the remants. If you have a air compressor then you could soda blast it. |
|
| Author: | zook_ute [ Sat Jan 07, 2012 10:56 am ] |
| Post subject: | Re: Getting silicon off |
give some carby cleaner a go, that stuff is good for everything |
|
| Author: | Jezza86 [ Sat Jan 07, 2012 11:34 am ] |
| Post subject: | Re: Getting silicon off |
TZAR wrote: If you have a air compressor then you could soda blast it.
i imagined 50% caustic soda in a paint sprayer... that would strip anything, including all the aluminium within 500m. glad to see its only baking soda! |
|
| Author: | rabrarley [ Sat Jan 07, 2012 12:12 pm ] |
| Post subject: | Re: Getting silicon off |
you can buy a rubber wheel that fits in your cordless drill, doest effect paint at all, i used it to take of glus from a jet ski matt, couldnt believe how easy it was, depending on how much ther is i would try an eraser just to see how it goes |
|
| Author: | sideways [ Sat Jan 07, 2012 1:42 pm ] |
| Post subject: | Re: Getting silicon off |
I use a wire wheel mounted in the drill or the sand blaster ($30 from Supercheap, you'l need a good air compressor though!). |
|
| Author: | wolf_rt [ Tue Jan 24, 2012 1:38 pm ] |
| Post subject: | Re: Getting silicon off |
dusting the silicone affected area with plaster dust will allow you to paint over it without fish eyes... doesnt do much for the gloss level though. |
|
| Author: | gregdixon [ Tue Jan 24, 2012 10:22 pm ] |
| Post subject: | Re: Getting silicon off |
Wire buff wheel |
|
| Author: | Hybrid [ Tue Jan 24, 2012 11:19 pm ] |
| Post subject: | Re: Getting silicon off |
sideways wrote: I use a wire wheel mounted in the drill or the sand blaster ($30 from Supercheap, you'l need a good air compressor though!).
Sand blasted a swingarm with a sticker on it back when I wasn't so sharp (16) and I had a permanent embossed sticker outline as it chewed the metal around it but did not a lot to the sticker. Does this not happen with the silicon? |
|
| Author: | want33s [ Wed Jan 25, 2012 2:01 am ] |
| Post subject: | Re: Getting silicon off |
Hybrid wrote: sideways wrote: I use a wire wheel mounted in the drill or the sand blaster ($30 from Supercheap, you'l need a good air compressor though!). Sand blasted a swingarm with a sticker on it back when I wasn't so sharp (16) and I had a permanent embossed sticker outline as it chewed the metal around it but did not a lot to the sticker. Does this not happen with the silicon? YEP. You cannot blast silicone off metal with sand or soda. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|