| auszookers.com http://auszookers.com/forum/ |
|
| barina / swift engine into sierra http://auszookers.com/forum/viewtopic.php?f=5&t=29879 |
Page 1 of 1 |
| Author: | bob9909 [ Wed Jan 25, 2012 12:11 am ] |
| Post subject: | barina / swift engine into sierra |
hey, just been down to the wreckers looking for a new engine for my zook. they had a bunch of barinas with the g13ba, but they didn't think that they would fit in the sierra anyone have any expierience with putting a east west engine out of a barina or swift into a sierra? |
|
| Author: | BlueSuzy [ Wed Jan 25, 2012 12:20 am ] |
| Post subject: | Re: barina / swift engine into sierra |
Most beepbeepbarina's are g13a, Same as swifts. (1324cc) later sierra's are g13ba (1298cc) Almost the same motor. With abit of searching, there is tones of info on them on here, and for simple converting. If the suzuki block starts with a G, Its one of the easiest swaps/conversions for a 1.3 sierra |
|
| Author: | bob9909 [ Wed Jan 25, 2012 12:29 am ] |
| Post subject: | Re: barina / swift engine into sierra |
thanks, but if the engine in the barina is a g13ba 1298cc would there be any issues putting it into the sierra? I know the east west engine, the distributor is straight, but can I just swap that with the one from the current engine if it doesn't fit nicely |
|
| Author: | BlueSuzy [ Wed Jan 25, 2012 12:33 am ] |
| Post subject: | Re: barina / swift engine into sierra |
With abit of searching, there is tonnes of kg of grams of info on them on here http://www.auszookers.com/index.php?nam ... g13a+dizzy |
|
| Author: | bob9909 [ Wed Jan 25, 2012 12:51 am ] |
| Post subject: | Re: barina / swift engine into sierra |
thanks, found lots of useful info searching. was downtown on my phone earlier seems like a bit of work to get it all up and running :s |
|
| Author: | Daves4wd [ Wed Jan 25, 2012 2:44 am ] |
| Post subject: | Re: barina / swift engine into sierra |
you need to change cam and dizzy and some other stuff go g16a still easy to do plus its worth it |
|
| Author: | bob9909 [ Wed Jan 25, 2012 2:47 am ] |
| Post subject: | Re: barina / swift engine into sierra |
Hey, while I have this thread open, and it seems that if I do put a barina engine in I will need the cam shaft from my current engine, does anyone have any tips for removing the counter sunk rocker securing screws? Being too loose seems to be the common issue but I can't budge them for the life of me and they are starting to strip out. In another thread I found a link to replacement screws from suzistore I think, but I need to get them out first :S |
|
| Author: | Daves4wd [ Wed Jan 25, 2012 2:53 am ] |
| Post subject: | Re: barina / swift engine into sierra |
use a hammer and impact driver or if there rotted drill a hole in the center and use a easy out maybe ive never done it i had to tighten mine |
|
| Author: | christover1 [ Wed Jan 25, 2012 6:45 am ] |
| Post subject: | Re: barina / swift engine into sierra |
My Sierras swift/barina had a multi V double pulley set up. I kept that on mine, so the swap to power steering and a 110amp alternator was easier. Otherwise need to fit the Sierra water pump, along with sump, oil pick up, cam and mounts etc. Note to self: drain oil before removing the sump 
  
|
|
| Author: | Mickc [ Wed Jan 25, 2012 9:11 pm ] |
| Post subject: | Re: barina / swift engine into sierra |
My spare G13a motor, from 88/89 Swift has dizzy mounted similar to sierra. The dizzy vaccum line is in different location, up against firewall. Carby needs to be rotated 180. Sierra parts required, water pump return pipe, engine mtg brackets, inlet and outlet manifoilds. |
|
| Author: | Mickc [ Wed Jan 25, 2012 9:12 pm ] |
| Post subject: | Re: barina / swift engine into sierra |
sump N pick up 2 |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|