| auszookers.com http://auszookers.com/forum/ |
|
| Gear change hard in Sierra transfer case http://auszookers.com/forum/viewtopic.php?f=5&t=32323 |
Page 1 of 1 |
| Author: | jonfromhamilton [ Thu May 03, 2012 9:26 pm ] |
| Post subject: | Gear change hard in Sierra transfer case |
So sometimes it is pretty hard to go from 4wd to 2wd in my stock standard transfer case. Next week I am putting 6:4 gears in it and while it is all to bits is there a piece i could organise now to swap out. if you guys can think of anything that might be an obvious cause for this difficulty in changed from 4 to 2 and visa versa. Chur |
|
| Author: | abclarke [ Thu May 03, 2012 9:28 pm ] |
| Post subject: | Re: gear change hard in t-case |
Is this while your still or moving? |
|
| Author: | Daves4wd [ Thu May 03, 2012 9:36 pm ] |
| Post subject: | Re: gear change hard in t-case |
Tcase bush might be buggered |
|
| Author: | christover1 [ Thu May 03, 2012 10:41 pm ] |
| Post subject: | Re: gear change hard in t-case |
Could be axle wind up. Or actually tail shafts wind up. Caused by differences in speeds front to rear on harder surfaces reverse a little forward a little, usually unjams it. But can be as said in posts above |
|
| Author: | christover1 [ Thu May 03, 2012 10:43 pm ] |
| Post subject: | Re: gear change hard in t-case |
Daves4wd wrote: Tcase bush might be buggered This is a common issue |
|
| Author: | abclarke [ Thu May 03, 2012 11:06 pm ] |
| Post subject: | Re: gear change hard in t-case |
christover1 wrote: Could be axle wind up. Or actually tail shafts wind up. Caused by differences in speeds front to rear on harder surfaces reverse a little forward a little, usually unjams it. But can be as said in posts above Haha had to do that quite a bit. Seems to be very picky at times 
|
|
| Author: | jonfromhamilton [ Sat May 05, 2012 5:17 pm ] |
| Post subject: | Re: Gear change hard in Sierra transfer case |
excuse my n00bness but you don't have to pull the t-case apart to change the bush ? |
|
| Author: | christover1 [ Sat May 05, 2012 5:26 pm ] |
| Post subject: | Re: Gear change hard in Sierra transfer case |
jonfromhamilton wrote: excuse my n00bness but you don't have to pull the t-case apart to change the bush ? No it can be done from inside the cabin, thru the tranny stick hole. Can't remember exact details. Easier after body lift. |
|
| Author: | jonfromhamilton [ Sun May 06, 2012 10:39 am ] |
| Post subject: | Re: Gear change hard in Sierra transfer case |
Mathew and I are putting the body lift in my Sierra on Thursday anyways  Thats if Widetread get my rims delivered tomorrow like they should have had done on Friday >_< |
|
| Author: | Daves4wd [ Sun May 06, 2012 2:36 pm ] |
| Post subject: | Re: Gear change hard in Sierra transfer case |
If you go from under neath and undo your switch then you and undo the thin that holds the stick in had to take mine on the side of a track should take about 15 mins to change it |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|