yes
| auszookers.com http://auszookers.com/forum/ |
|
| Front tailshaft http://auszookers.com/forum/viewtopic.php?f=5&t=32452 |
Page 1 of 1 |
| Author: | Deego [ Wed May 09, 2012 1:02 pm ] |
| Post subject: | Front tailshaft |
With your front tailshaft that goes to your transfer case to your front diff.when I took it out does the spline suppose to just come out out the shaft |
|
| Author: | shep [ Wed May 09, 2012 1:05 pm ] |
| Post subject: | Re: Front tailshaft |
yes
|
|
| Author: | shep [ Wed May 09, 2012 1:06 pm ] |
| Post subject: | Re: Front tailshaft |
it has to go back together the same |
|
| Author: | Deego [ Wed May 09, 2012 1:10 pm ] |
| Post subject: | Re: Front tailshaft |
So you just can't slide it back into place. |
|
| Author: | zooky08 [ Wed May 09, 2012 1:13 pm ] |
| Post subject: | Re: Front tailshaft |
you can but i say it be unbalance |
|
| Author: | Deego [ Wed May 09, 2012 1:16 pm ] |
| Post subject: | Re: Front tailshaft |
Ok thanks guys |
|
| Author: | Deego [ Wed May 09, 2012 1:53 pm ] |
| Post subject: | Re: Front tailshaft |
Are all the sierras got the same front tailshaft |
|
| Author: | shep [ Wed May 09, 2012 1:58 pm ] |
| Post subject: | Re: Front tailshaft |
Deego wrote: Are all the sierras got the same front tailshaft no. 1.0 have a solid shaft with 8mm bolt holes. 1.3 nt has a hollow shaft with 8mm bolt holes and 1.3 wt has hollow shaft with 10mm bolt holes. coilys probably have shafts made out of cheese with paper clips to hold it together. |
|
| Author: | Deego [ Wed May 09, 2012 2:00 pm ] |
| Post subject: | Re: Front tailshaft |
Does the 1986 have the same as the 1990 models |
|
| Author: | shep [ Wed May 09, 2012 2:02 pm ] |
| Post subject: | Re: Front tailshaft |
Deego wrote: Does the 1986 have the same as the 1990 models no |
|
| Author: | Gwagensteve [ Wed May 09, 2012 2:13 pm ] |
| Post subject: | Re: Front tailshaft |
86 and 90 have the same shaft and unis, it's only the flanges that re different. Steve. |
|
| Author: | shep [ Wed May 09, 2012 2:15 pm ] |
| Post subject: | Re: Front tailshaft |
you cant un bolt a tailshaft from a 1990 sierra and bolt it into a 1986 sierra |
|
| Author: | royce [ Wed May 09, 2012 2:57 pm ] |
| Post subject: | Re: Front tailshaft |
If you want to replace the shaft cauyse you pulled it apart and now dont know what to do look closely where the 2 bits slide together, any luck youll see apunch mark on both bits, lines these up and slide it together |
|
| Author: | Deego [ Wed May 09, 2012 4:18 pm ] |
| Post subject: | Re: Front tailshaft |
I'm looking at a 1986 model and I wAnt the tailshaft to go on my 1990. |
|
| Author: | zooky08 [ Wed May 09, 2012 4:22 pm ] |
| Post subject: | Re: Front tailshaft |
What's wrong with your one? |
|
| Author: | Deego [ Wed May 09, 2012 4:30 pm ] |
| Post subject: | Re: Front tailshaft |
The spline is real slopping you can wiggles around when you shake the tailshaft |
|
| Author: | shep [ Wed May 09, 2012 4:56 pm ] |
| Post subject: | Re: Front tailshaft |
Deego wrote: The spline is real slopping you can wiggles around when you shake the tailshaft mine has been like that for years i just dont go over 50kph with the hubs locked 
|
|
| Author: | Deego [ Wed May 09, 2012 5:16 pm ] |
| Post subject: | Re: Front tailshaft |
What about 4wding |
|
| Author: | shep [ Wed May 09, 2012 5:21 pm ] |
| Post subject: | Re: Front tailshaft |
Deego wrote: What about 4wding i dont drive fast in the bush. |
|
| Author: | royce [ Wed May 09, 2012 8:50 pm ] |
| Post subject: | Re: Front tailshaft |
grease it up, seems most people forget they need grease in em |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|