auszookers.com
http://auszookers.com/forum/

transfer needle bearing size
http://auszookers.com/forum/viewtopic.php?f=5&t=35178		 Page 1 of 1
Author:  Joshyboy26 [ Wed Aug 22, 2012 9:56 pm ]
Post subject:  transfer needle bearing size
Its a long shot but does anyone know the dimensions or the numbers off the needle bearing that runs on the main shaft. ( the bigger needle bearing on the biggest shaft)
Thanks in advance
Author:  303zuke [ Thu Aug 23, 2012 1:23 am ]
Post subject:  Re: transfer needle bearing size
Long shot alright. What vehicle for starters?
Author:  Joshyboy26 [ Thu Aug 23, 2012 6:34 am ]
Post subject:  Re: transfer needle bearing size
Sierra wt
Author:  Scales [ Thu Aug 23, 2012 7:36 am ]
Post subject:  Re: transfer needle bearing size
I got my old bearings on my bench. I'll have a look shortly
Author:  Scales [ Thu Aug 23, 2012 7:55 am ]
Post subject:  Re: transfer needle bearing size
Okay,
well out of all the needle bearings i took out, the biggest ones i had on the bench were a set of 2. both identical. and SGP p/n is 29985-80050 I didnt get any measurements cos my vernier ran out of batterys.

They were the only bearings in the rebuild kit that were NOT koyo, so im guessing they were suzuki only bits but cant be 100% on that. I can get measurements later if that info is not sufficient.

Keep in mind i cant confirm these are actually the ones you are chasing, i just went for whichever were the biggest.
Author:  Fatzook [ Thu Aug 23, 2012 9:53 am ]
Post subject:  Re: transfer needle bearing size
The needle roller bearings on the countershaft ( prop shaft/ idle shaft ) are identicle and are approx. 31mm long, 33OD, 27ID.

The needle roller bearings on the main output shaft are larger, with the one on the front output end being approx 40mm long and ID of 44mm. And the other being approx 35mm long with ID of 44mm also.

All these dimensions were measured through plastic, but should be good enough to identify a bearing from a list of SGP#'s.
Author:  Joshyboy26 [ Thu Aug 23, 2012 11:03 am ]
Post subject:  Re: transfer needle bearing size
Sweet thanks guys. Its just suziworld said he couldn get one so im just chasing it up through random bearing shops but im not home to measure it cheers.
Author:  Fatzook [ Thu Aug 23, 2012 11:52 am ]
Post subject:  Re: transfer needle bearing size
They are VERY hard to find, as its not a common size.

PM Weaves http://www.auszookers.com/forum/memberlist.php?mode=viewprofile&u=377 .

If he can't get them, then they are genuine only.
Author:  Joshyboy26 [ Fri Aug 24, 2012 9:14 am ]
Post subject:  Re: transfer needle bearing size
Well i rung around and it turns out its a genuine only bearing and i have to wait for it from japan dam!

So just for future reference the bearing is 35mm id 41mm od and 40mm long. I do not know the numbers though.
Author:  Scales [ Fri Aug 24, 2012 10:01 am ]
Post subject:  Re: transfer needle bearing size
Joshyboy26 wrote:
I do not know the numbers though.


Scales wrote:
and SGP p/n is 29985-80050


guess you missed my post?
Author:  Fatzook [ Fri Aug 24, 2012 4:53 pm ]
Post subject:  Re: transfer needle bearing size
Joshyboy26 wrote:
Well i rung around and it turns out its a genuine only bearing and i have to wait for it from japan dam!

So just for future reference the bearing is 35mm id 41mm od and 40mm long. I do not know the numbers though.



10 days from lowrange.
Author:  Scales [ Sat Aug 25, 2012 4:53 pm ]
Post subject:  Re: transfer needle bearing size
try 4wd_products on ebay. they sold me the kit, sure they could sell you the ones your chasing.
Author:  Joshyboy26 [ Sat Sep 01, 2012 5:34 pm ]
Post subject:  Re: transfer needle bearing size
those bearings that are identical run on the intermediate shaft and are not the ones i was after but thanks anyway. suziworld is getting me one now thanks guys
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/