auszookers.com
http://auszookers.com/forum/

2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny?
http://auszookers.com/forum/viewtopic.php?f=5&t=36108		 Page 1 of 1
Author:  Dr_Snapid [ Wed Oct 03, 2012 1:32 pm ]
Post subject:  2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny?
Hi all.

Looks like I have damaged my motor after an overheat. Head gasket (at least) or cracked head. M13a non-vvt.

This has happened before to me and cost $1500+ last time to have a mechanic do it including getting the head shaved. I'm thinking I might consider an engine swap instead and at least get some gains for my money this time.

There is several threads on here regarding the swap and it looks like something my mates and I could handle but the difficult detail is my auto tranny.

Does anyone know of an example where someone has done the engine swap with an auto jimny? I have found a few discussions but noone who closed the deal..
Author:  Jazzor [ Wed Oct 03, 2012 4:39 pm ]
Post subject:  Re: 2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny
Yea same re no-one else has done it yet. Its going to be on the cards when I run out of other things to do.

Not a great situation for you :(. Watching this thread :).
Author:  Gwagensteve [ Wed Oct 03, 2012 5:02 pm ]
Post subject:  Re: 2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny
My understanding is that the Jimny auto is right at its torque ceiling with an m13. With lots of cooling capacity, a temp gauge, and sensible use (ie not labouring in high range first on steep hills) it might last ok, but I'd be looking for a spare just in case.

Gregc is slowly working towards dropping a g16b in front of his Jimny auto. His auto already gets scary hot so he's doubling his cooling capacity.

Physically/mechanically it should be straightforward.
Author:  joeblow [ Wed Oct 03, 2012 7:24 pm ]
Post subject:  Re: 2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny
I'm about to throw an AW4 behind an M13 soon. I'll be sure to post a thread on how much of a pain, or how easy it might be.
Author:  Dr_Snapid [ Wed Oct 03, 2012 7:45 pm ]
Post subject:  Re: 2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny
My car is off the road now, I dont think i'll have time to see how others go with their swaps. if i'm going to do one it will be within weeks...

So it will be into the dark I venture (if I go there at all)
Author:  Fatzook [ Wed Oct 03, 2012 8:15 pm ]
Post subject:  Re: 2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny
Are you fitting an M15 instead of fixing the M13 again?
Author:  Dr_Snapid [ Wed Oct 03, 2012 8:37 pm ]
Post subject:  Re: 2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny
Fatzook wrote:
Are you fitting an M15 instead of fixing the M13 again?


Considering it
Author:  Fatzook [ Wed Oct 03, 2012 8:40 pm ]
Post subject:  Re: 2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny
An M15a will be cheaper than another rebuild.
Author:  Dr_Snapid [ Wed Oct 03, 2012 9:06 pm ]
Post subject:  Re: 2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny
Yes as long as the tranny doesnt shit itself soon after
Author:  Fatzook [ Wed Oct 03, 2012 9:27 pm ]
Post subject:  Re: 2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny
Dr_Snapid wrote:
Yes as long as the tranny doesnt shit itself soon after



I think if you drive it sensibly you should be fine.
Author:  Dr_Snapid [ Thu Oct 04, 2012 9:26 am ]
Post subject:  Re: 2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny
Got a M15a locally from a Holden Cruze, 111000kms for $625 :)

Everyone cross ya fingers the auto bolts up (and holds up)

I will put progress in my build thread here http://auszookers.com/forum/viewtopic.php?f=4&t=31455&p=660960#p660960
Author:  Fatzook [ Thu Oct 04, 2012 9:33 am ]
Post subject:  Re: 2003 Jimny engine swap (m15a,M16a,m18a) with auto tranny
Armsup
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/