Ive been doing a Baleno swap in my Sierra
I have fitted the tacho to the sierra cluster but Im trying ti figur out what wire is what on the back of the tacho I know there is a signal, +, - and anyone show me in the pic below?
| auszookers.com http://auszookers.com/forum/ |
|
| Baleno tacho into Sierra cluster http://auszookers.com/forum/viewtopic.php?f=5&t=38734 |
Page 1 of 1 |
| Author: | jimbo_jones [ Sun Feb 03, 2013 8:44 am ] |
| Post subject: | Baleno tacho into Sierra cluster |
Ive been doing a Baleno swap in my Sierra I have fitted the tacho to the sierra cluster but Im trying ti figur out what wire is what on the back of the tacho I know there is a signal, +, - and anyone show me in the pic below?
|
|
| Author: | CairnsZook [ Sun Feb 03, 2013 11:56 am ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
I can't remember which is which. But I think I worked it out by which colour wire comes off each contact. Obviously not the colour of the wires you have put on... Trace them to the plug, then from the wiring diagram find out which colour is for each signal. |
|
| Author: | BlueSuzy [ Sun Feb 03, 2013 3:25 pm ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
I did my last one via trial and error 
|
|
| Author: | shark [ Sun Feb 03, 2013 6:31 pm ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
Crap I had my dash apart today too. If I get time during the week I will have a look |
|
| Author: | jimbo_jones [ Sun Feb 03, 2013 8:28 pm ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
shark wrote: Crap I had my dash apart today too. If I get time during the week I will have a look cheers |
|
| Author: | jimbo_jones [ Thu Feb 07, 2013 8:40 am ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
Any one have any more info on this? |
|
| Author: | shark [ Thu Feb 07, 2013 1:34 pm ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
Sorry mate been bulk busy. Pm me tonight and i will have a gander, im pretty srue the drawings are still on my work bench somehwere |
|
| Author: | jimbo_jones [ Thu Feb 07, 2013 3:03 pm ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
shark wrote: Sorry mate been bulk busy. Pm me tonight and i will have a gander, im pretty srue the drawings are still on my work bench somehwere That would be awsome |
|
| Author: | shark [ Thu Feb 07, 2013 11:06 pm ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
Okay mate now without taking my dash apart to double check I still had the drawing on my work bench. Looking from the back Top is earth Right is power Left is signal No responsibility is taken although initially I had the power and earth swapped around and it didn't do any damage |
|
| Author: | jimbo_jones [ Fri Feb 08, 2013 7:10 am ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
Thanks mate your a big help |
|
| Author: | BlueSuzy [ Fri Feb 08, 2013 8:15 am ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
Only 6 combinations to test anyway |
|
| Author: | shark [ Fri Feb 08, 2013 8:38 am ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
Yeah it wasn't difficult. I just winged it:) |
|
| Author: | kenzook [ Thu Jan 28, 2016 4:47 pm ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
so was this right? im doing now and spent too frigging long going back n forth looking caus i think sharks is wrong. looking directly at the back of the baleno cluster doesn't match or im fucking confused jimbo what did u hook up n where? i think i over complicate things/look into things too much and then i cant make a call, i cant just wing it. |
|
| Author: | kenzook [ Thu Jan 28, 2016 5:20 pm ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
i used the colored wires for easy identification, the brown signal wire lands on the no 3 spot in pic, but that is not shark said hes got pwr to the right which is number 3. and the other 2 are black with white stripe and black with orange stripe. |
|
| Author: | Scrawny [ Sat Jan 30, 2016 10:17 am ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
I think he meant right was #2, which would make sense. Looking at the back of the Baleno cluster it looks like he's right #1- earth #2- power #3- signal |
|
| Author: | kenzook [ Sat Jan 30, 2016 12:26 pm ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
ok cool. that looks like it works. #2 is a black with white stripe wire (on baleno diagram) that goes to ignition so yeah thats pwr. loks like i ASSUMED shark rotated it so it had a top,left and right cool thanks scrawn |
|
| Author: | Scrawny [ Sat Jan 30, 2016 1:42 pm ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
How are you mounting the tacho? |
|
| Author: | kenzook [ Sun Jan 31, 2016 2:42 pm ] |
| Post subject: | Re: Baleno tacho into Sierra cluster |
just screwed to the sj80 face plate and clear mount to hold it in place but then just have to run the wires like above |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|