auszookers.com
http://auszookers.com/forum/

how to remove rear axle bearings
http://auszookers.com/forum/viewtopic.php?f=5&t=607		 Page 1 of 1
Author:  josh9465 [ Mon Jan 08, 2007 12:42 am ]
Post subject:  how to remove rear axle bearings
i have a 91 sierra.
ive just take out the rear axles. the bearings have 0.5 to 1mm play in them

do i need special tools to remove and replace..

im thinking i need some sort of press or something.

or is it easier to take to mechanic to remove and replace.
Author:  steve [ Mon Jan 08, 2007 12:44 am ]
Post subject:  Re: how to remove rear axle bearings
i haven't done one for a while but from memory, we bashed the crap out of it to get it off and used a press to get the new one on.
Author:  royce [ Mon Jan 08, 2007 2:20 am ]
Post subject:  Re: how to remove rear axle bearings
ive always had access to a press and the proper tools and never used em :wink:

to remove, sit bearing on something solid, wrap tightly in rags, put glasses on and smash with hammer :twisted:

then the 2 inner bits you have left, cut a groove a few mm thick with an angle grinder, then bash crap out of said groove with hammer and cold chisel, this will spread it and crack the races so they will slide off

to put one on I just use a bit of 32NB thick wall pipe and bash em on, prob not the best way but its easy and the bearing never twists or gets stuck
Author:  josh9465 [ Mon Jan 08, 2007 11:58 pm ]
Post subject:  Re: how to remove rear axle bearings
ok thanks for that.
Author:  Rapson [ Fri Nov 09, 2007 5:24 pm ]
Post subject:  Re: how to remove rear axle bearings
Hey guys,
Excuse my ignorance but what is 32NB Wall Pipe? I am assuming it is the size of a piece of p[ipe.

If I go the the metal joint down the road will they know what I am after?

Cheers
Rapson
Author:  royce [ Fri Nov 09, 2007 5:29 pm ]
Post subject:  Re: how to remove rear axle bearings
yeah 32nb is 32mm nominal bore, basically 1 1/4 water pipe

will be about 42mm OD and 5mm wall thickness, check thats the right size to slip over the axle 1st though cause I could have the wrong size
Author:  Rapson [ Fri Nov 09, 2007 5:37 pm ]
Post subject:  Re: how to remove rear axle bearings
Beauty, thanks Royce,

I think when I take the axel out I will take it to the metal shop and get the right size pipe.

So the pipe should be pretty snug around the axel so as to bash the inner race of the bearing down.
Author:  royce [ Fri Nov 09, 2007 5:46 pm ]
Post subject:  Re: how to remove rear axle bearings
yeah you want it to hit the inner race and not the seal section of bearing, the pipe will either be a pretty good fit or way to big, there arent too many different sizes when it comes to pipe
Author:  Westie [ Mon Nov 12, 2007 11:31 pm ]
Post subject:  Re: how to remove rear axle bearings
Ahh good work Royce... At what year Motor Mechanics Apprentices do you learn that procedure, or was that in Bush Mechanics School.

That is why they call on Royce when things go BANG in the bush Oh and Caboolture :lol: :lol: :lol:
Author:  royce [ Tue Nov 13, 2007 12:33 am ]
Post subject:  Re: how to remove rear axle bearings
this is what you learn when you have a job to do and bugger all of the correct tools to do it with
Author:  Westie [ Tue Nov 13, 2007 3:13 am ]
Post subject:  Re: how to remove rear axle bearings
Yep know what ya talkin about there i have a shed full of the wrong tools but I do have a welder grinder and some big hammers that tend to do the job :lol:
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/