it is possible if you get a new crush tube and set the diff up from scratch.
if you do you may as well get a new pinion bearing and seal as well.
| auszookers.com http://auszookers.com/forum/ |
|
| Help with diffs and driveshafts. http://auszookers.com/forum/viewtopic.php?f=5&t=7121 |
Page 1 of 1 |
| Author: | Junior_91 [ Sat Oct 10, 2009 11:18 pm ] |
| Post subject: | Help with diffs and driveshafts. |
I just swapped my diffs under my 1993 SWB WT and my 1987 LWB WT and the tail shaft doesn't bolt up is this becuase they have a different pinnion yoke and are they interchangeable??? Any help would be greatly appreciated. |
|
| Author: | Gwagensteve [ Sat Oct 10, 2009 11:54 pm ] |
| Post subject: | Re: Help with diffs and driveshafts. |
correct. WT and NT have different pinion flanges. The easy way to fix this is to swap the transfer flanges, or swap the yokes on your tailshafts to suit, or swap 1/2 your tailshafts so the short end is NT and the long end is WT. Don't pull the pinion flanges off and swap them - you'll screw up the pinion bearing preload and destroy the diffs. Steve. |
|
| Author: | Junior_91 [ Sun Oct 11, 2009 12:33 am ] |
| Post subject: | Re: Help with diffs and driveshafts. |
But if i know how to do it properly i can change them? I have installed a locker into it so i know what i am doing is this possible? |
|
| Author: | shep [ Sun Oct 11, 2009 1:37 am ] |
| Post subject: | Re: Help with diffs and driveshafts. |
it is possible if you get a new crush tube and set the diff up from scratch. if you do you may as well get a new pinion bearing and seal as well.
|
|
| Author: | steak_knife [ Sun Oct 11, 2009 3:29 am ] |
| Post subject: | Re: Help with diffs and driveshafts. |
shep wrote: it is possible if you get a new crush tube and set the diff up from scratch.
if you do you may as well get a new pinion bearing and seal as well.X2, good on ya shep.
|
|
| Author: | Junior_91 [ Sun Oct 11, 2009 5:38 am ] |
| Post subject: | Re: Help with diffs and driveshafts. |
shep wrote: it is possible if you get a new crush tube and set the diff up from scratch.
if you do you may as well get a new pinion bearing and seal as well.So it will fit? Just wanna make sure. |
|
| Author: | Gwagensteve [ Sun Oct 11, 2009 12:39 pm ] |
| Post subject: | Re: Help with diffs and driveshafts. |
Yes, it will fit, but that's a whole lot of work to "fix" something that doesn't need fixing. If you are pulling your diffs apart anyway, go for your life, but why open up a diff when there's no need? You didn't explain which way round you were swapping, but the larger WT flange is superior - it runs bigger bolts- so if your diffs have the large flange that's what I'd be keeping. Steve. |
|
| Author: | xedent [ Thu Mar 10, 2011 10:02 am ] |
| Post subject: | Re: Help with diffs and driveshafts. |
How do you torque these up if i have the new crush tube etc do you have to take the center out or what ? |
|
| Author: | mr_ron [ Fri Mar 11, 2011 6:58 am ] |
| Post subject: | Re: Help with diffs and driveshafts. |
I went from NT diff centerS(Small flange) in NT housing to the wt diff centers(big flange).. i just got some WT drive shafts and they fit like the NT ones.. |
|
| Author: | BlueSuzy [ Fri Mar 11, 2011 9:08 pm ] |
| Post subject: | Re: Help with diffs and driveshafts. |
Lwb Wt flanges are Nt. Including jackshaft and transfer flanges. Swb Wt flanges are all Wt. |
|
| Author: | 31zook [ Fri Mar 11, 2011 9:10 pm ] |
| Post subject: | Re: Help with diffs and driveshafts. |
but 1.3 lwb sierra's are nt flanges
|
|
| Author: | shep [ Fri Mar 11, 2011 9:48 pm ] |
| Post subject: | Re: Help with diffs and driveshafts. |
my LWB has wt diff flanges but only because it has wt diffs 
my front tail shaft is all wt and my rear is half wt and half nt because i wanted to keep the transfer handbrake. |
|
| Author: | BlueSuzy [ Fri Mar 11, 2011 11:40 pm ] |
| Post subject: | Re: Help with diffs and driveshafts. |
31zook wrote: but 1.3 lwb sierra's are nt flanges
All lwb are Nt flanges.. |
|
| Author: | TZAR [ Sat Mar 12, 2011 4:07 am ] |
| Post subject: | Re: Help with diffs and driveshafts. |
BlueSuzy wrote: 31zook wrote: but 1.3 lwb sierra's are nt flanges All lwb are Nt flanges.. what about maruti's? aren't they lwb with wt stuff under them in the later models???? |
|
| Author: | remydog05 [ Mon May 23, 2011 3:13 am ] |
| Post subject: | Re: Help with diffs and driveshafts. |
Whats the easy way to tell if the flange you have is WT or NT? The bolts are bigger in WT? But does the flange also measure larger?? |
|
| Author: | JrZook [ Mon May 23, 2011 3:49 am ] |
| Post subject: | Re: Help with diffs and driveshafts. |
BlueSuzy wrote: Lwb Wt flanges are Nt. Including jackshaft and transfer flanges.
Swb Wt flanges are all Wt. 88.5 no deal |
|
| Author: | Fatzook [ Mon May 23, 2011 4:11 am ] |
| Post subject: | Re: Help with diffs and driveshafts. |
BlueSuzy wrote: 31zook wrote: but 1.3 lwb sierra's are nt flanges All lwb are Nt flanges.. You've been around zooks long enough to know that even suzuki doesn't follow their own rules
I've seen quite a few oddball zooks with parts from other models OEM fitted. And 1L LWB are not the same flange as 1.3 LWB. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|