auszookers.com
http://auszookers.com/forum/

GTI to mazda dizzy cap
http://auszookers.com/forum/viewtopic.php?f=5&t=7416		 Page 1 of 1
Author:  jimbo_jones [ Fri Oct 23, 2009 2:06 am ]
Post subject:  GTI to mazda dizzy cap
I did the 323 cap on mine and my mate did the angle drive on his I think for the money the Mazda cap wins hands down but don't think for a second its a straight bolt up
the Mazda cap is 2 small and needs to be opened up with a die grinder go slow and keep trial fitting it its about 2mm that has to come of you will also need the Mazda rotor button now to get this to fit the gti dizzy you will have to crack open the gti rotor button and remove the brass sleeve, on the Mazda rotor there is a little metal bit where it sits on the shaft remove this and discard there is also a little lug in there this also needs to be removed (I put a flat screwdriver in there and snapped it out) then you need to enlarge the hole with a drill not to much the brass sleeve out of the gti rotor need to be taped in make shoure the screw hole is in the right spot as its a press fit and wont come back out once the brass sleeve is fitted drill a hole for the locating screw and fit new rotor button and cap

now I did all this but see how the mazda cap has the numbers on it is it the same firing order as the gti or do I need to swap leads around? :?

Image
Author:  steak_knife [ Fri Oct 23, 2009 2:28 am ]
Post subject:  Re: GTI to mazda dizzy cap
Look`s the same as the one I played with & in was in order, same that is.
Most normal 4cyl eng are 1 3 4 2, if you put the rotor on 1 & turn by hand, watch which way it go`s, then you should be able to figure out if it`s rite.

by the sound`s of the mod`s you did it`s the same cap he used..

Have fun..
Author:  jimbo_jones [ Fri Oct 23, 2009 2:33 am ]
Post subject:  Re: GTI to mazda dizzy cap
hmmmm that what I thought just wanted to confirm it
Author:  steak_knife [ Fri Oct 23, 2009 2:39 am ]
Post subject:  Re: GTI to mazda dizzy cap
jimbo_jones wrote:
hmmmm that what I thought just wanted to confirm it


Good, just hurry up & get it going :lol:
Author:  canberramav [ Fri Oct 23, 2009 3:32 pm ]
Post subject:  Re: GTI to mazda dizzy cap
Good tech

This mod can be a bit confusing. Im about to do it to my dads zook. What is the height of the rotor after you have done this mod?

Just wondering how good the clearance will be to the dizzy cap

Cheers
Author:  jimbo_jones [ Fri Oct 23, 2009 5:29 pm ]
Post subject:  Re: GTI to mazda dizzy cap
Don't know I didn't check
Author:  jimbo_jones [ Sat Oct 24, 2009 12:52 am ]
Post subject:  Re: GTI to mazda dizzy cap
Got the GTI motor to fire up but only runs for about 1 second then stalls anyone got any
idea's?
Author:  steak_knife [ Sat Oct 24, 2009 1:02 am ]
Post subject:  Re: GTI to mazda dizzy cap
Have a look here, it`s the on I played with.
http://auszookers.com/index.php?name=Fo ... pic&t=6165
Author:  jimbo_jones [ Sat Oct 24, 2009 3:31 am ]
Post subject:  Re: GTI to mazda dizzy cap
steknig wrote:
Have a look here, it`s the on I played with.
http://auszookers.com/index.php?name=Fo ... pic&t=6165


that dosnt tell me what it was what did you do to fix your prob?
Author:  steak_knife [ Sat Oct 24, 2009 4:30 pm ]
Post subject:  Re: GTI to mazda dizzy cap
I don`t have a pin out for the ecu, but from memory A12, B16,B12 & 1 of the earth`s were wrong`s, I think A12 is a neg signal & on the diagram it look`s like it go's to ing voltage , some thing else on the diagrahm was a neg triger for the main relay out of the ecu, it looked like 12v ing.

Hope that help`s
Author:  jimbo_jones [ Sat Oct 24, 2009 4:36 pm ]
Post subject:  Re: GTI to mazda dizzy cap
going to take it in the work on monday and put it on the diagnostic machine and the auto elec next door to work will have a look at it then I suck @ electrics
Author:  steak_knife [ Sat Oct 24, 2009 4:37 pm ]
Post subject:  Re: GTI to mazda dizzy cap
jimbo_jones wrote:
going to take it in the work on monday and put it on the diagnostic machine and the auto elec next door to work will have a look at it then I suck @ electrics


I`m not to bad but this thing had me stuffed for a week... 8O
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/