| auszookers.com http://auszookers.com/forum/ |
|
| Shed clean out Mk9! Updated 1st http://auszookers.com/forum/viewtopic.php?f=7&t=22098 |
Page 1 of 1 |
| Author: | remydog05 [ Thu May 19, 2011 11:14 am ] |
| Post subject: | Shed clean out Mk9! Updated 1st |
Gone through shed again and its time to get rid of more junk, and clear space for the build! Also have 3 sets of Transfer arms $20 per set. GV J20A radiator and fan and shroud $50 came from running car so should be ok, rad is not in prime cond. GRAND VITARA FRONT BRAKES $50 Disk and Calipers, great cond! Sierra Baleno or swift (not sure) Front seats OK Condition $50 2pin center good nic, $30. (came out for airlocker) Contact via PM. Will freight at BUYERS risk, there will be a charge for my time etc. Buyer to organize the freight company. Location is 3199, Vic Pics on Request, they are taking ages to load so I will just put up the ones you need. |
|
| Author: | Built4thrashing [ Thu May 19, 2011 11:44 am ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc etc |
the 2 pin ctr. is it 22 or 26 spline. if its 26 ill take it. |
|
| Author: | anto86 [ Thu May 19, 2011 11:45 am ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc etc |
long shot but can i have the flanges (WT) off the t/case or any spares you might have? $? |
|
| Author: | remydog05 [ Thu May 19, 2011 11:46 am ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc etc |
Built4thrashing wrote: the 2 pin ctr. is it 22 or 26 spline. if its 26 ill take it.
mmm good question! I think it came from the front one so prob a 22? |
|
| Author: | remydog05 [ Thu May 19, 2011 11:47 am ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc etc |
anto86 wrote: long shot but can i have the flanges (WT) off the t/case or any spares you might have? $?
Sorry mate Im in the same boat! Im gunna have to find some also. By the way whats the difference?? Bolts holes line up as far as I know but what else? |
|
| Author: | remydog05 [ Thu May 19, 2011 11:50 am ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc et |
Sorry!~ Someone just sent me a PM and I deleted it before I read it! Please send again! |
|
| Author: | anto86 [ Thu May 19, 2011 12:01 pm ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc etc |
remydog05 wrote: anto86 wrote: long shot but can i have the flanges (WT) off the t/case or any spares you might have? $? Sorry mate Im in the same boat! Im gunna have to find some also. By the way whats the difference?? Bolts holes line up as far as I know but what else? I'm trying to find out for sure without tearing the transfer out of my mates. But I've been told that the NT flanges are a smaller diameter and a different bolt pattern to the WT ones. Apparently you can still drill NT's to suit a WT or coily driveshaft. I'm trying to confirm this before I go any further though. As for coily flanges, they fit on the same splined shaft but part of the flange is the actual sealing surface, and they are much shallower, so when you put them on a WT transfer and whack the nuts on, the flanges slide back and forward heaps. Lowrange has new ones but at $89 each they can get fucked. |
|
| Author: | zuk_244 [ Thu May 19, 2011 1:42 pm ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc etc |
Yeah narrow track flanges have the holes abit closer to the center, which is why you cant just put the WT shafts on them. The good news is that the collar that locates the shaft into the center is the same size, which means you can slot out the NT holes or drill in new ones and the shaft will locate in the right spot and not vibrate. |
|
| Author: | oozuk [ Thu May 19, 2011 8:57 pm ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc etc |
Just unbolt the NT flanges from the transfer and fit the WT flanges from your old transfer, problem solved. |
|
| Author: | remydog05 [ Thu May 19, 2011 10:05 pm ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc etc |
oozuk wrote: Just unbolt the NT flanges from the transfer and fit the WT flanges from your old transfer, problem solved.
is there a way you can measure what is what? I have about 6 shafts here and 3 TC cases, just trying to figure out what is what! |
|
| Author: | oozuk [ Thu May 19, 2011 10:21 pm ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc etc |
NT flanges have M6 tailshaft bolt holes for 12mm headed bolts and a trans brake. WT Flanges are M8 and a larger bolt spacing on there flanges for the 14mm bolt WT tail shaft yokes are the same as SJ80 & Vitara |
|
| Author: | anto86 [ Fri May 20, 2011 3:44 am ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc etc |
oozuk wrote: Just unbolt the NT flanges from the transfer and fit the WT flanges from your old transfer, problem solved.
Would do that but i drive a coily. :@ |
|
| Author: | remydog05 [ Fri May 20, 2011 11:29 am ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc |
Also have 2 x 2pin centers and are 22 spline. Let me know if you want them, come and get them! |
|
| Author: | remydog05 [ Sat May 21, 2011 11:34 pm ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bull&towbars/etc et |
All going on ebay today TC sold |
|
| Author: | remydog05 [ Sun May 22, 2011 2:35 am ] |
| Post subject: | Re: Shed clean out Mk8! 6.5/Panels/Seats/bullbar/etc etc |
Towbar gone |
|
| Author: | remydog05 [ Sun May 22, 2011 11:17 am ] |
| Post subject: | Re: Shed clean out Mk8! Updated 22nd |
Feel Free to ask for a package deal. All items now listed on ebay also. |
|
| Author: | remydog05 [ Wed Jun 01, 2011 10:23 am ] |
| Post subject: | Re: Shed clean out Mk9! Updated 1st |
Updated |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|