i did the same. now need a pair of pliers to grasp the bottom bit
| auszookers.com http://auszookers.com/forum/ |
|
| M series dipstick http://auszookers.com/forum/viewtopic.php?f=8&t=48447 |
Page 1 of 1 |
| Author: | royce [ Sat Nov 15, 2014 8:24 pm ] |
| Post subject: | M series dipstick |
So, broke the top of my dipstick, anyone got one floating around after a Conversion? Liana so might be the same. May as well see if somebody has a fuel rail with a return while I am here |
|
| Author: | GT_Tony [ Sun Nov 16, 2014 6:50 am ] |
| Post subject: | Re: M series dipstick |
i did the same. now need a pair of pliers to grasp the bottom bit
|
|
| Author: | Gromet [ Sun Nov 16, 2014 6:59 am ] |
| Post subject: | Re: M series dipstick |
i did this whiping it down... might help to say what cc the engine you have is as that will be the dipstick you need. |
|
| Author: | jimny_timmy [ Sun Nov 23, 2014 8:15 pm ] |
| Post subject: | Re: M series dipstick |
I'll check out the dipstick tomorrow off my m18 and see if it's the same as the jimny. You're welcome to it if it is. Is it out of your swift? |
|
| Author: | royce [ Sun Nov 23, 2014 8:55 pm ] |
| Post subject: | Re: M series dipstick |
Yeah for the swift, just measure from the stopper to the fill mark to see if they are the same. |
|
| Author: | jimny_timmy [ Sun Nov 23, 2014 8:55 pm ] |
| Post subject: | Re: M series dipstick |
Too easy 
|
|
| Author: | Paulw [ Mon Nov 24, 2014 5:02 pm ] |
| Post subject: | Re: M series dipstick |
Might be easier to just get a brand new one as Suzuki charged me only $18 (I snapped mine doing the swap to a M15a) |
|
| Author: | Gromet [ Mon Nov 24, 2014 5:58 pm ] |
| Post subject: | Re: M series dipstick |
Yeh, My M15a one was like 1cm longer then the old M13a. |
|
| Author: | zukenutter [ Mon Nov 24, 2014 8:54 pm ] |
| Post subject: | Re: M series dipstick |
Liana dipstick left, Jimny on the right 
|
|
| Author: | Gromet [ Mon Nov 24, 2014 8:56 pm ] |
| Post subject: | Re: M series dipstick |
yeh so obviously if you put the Liana engine in. use the Liana dipstick... |
|
| Author: | zukenutter [ Mon Nov 24, 2014 9:02 pm ] |
| Post subject: | Re: M series dipstick |
Actually no. The Liana stick is matched to the sump, different location on the rocker cover too. |
|
| Author: | Gromet [ Mon Nov 24, 2014 9:04 pm ] |
| Post subject: | Re: M series dipstick |
ohk, because I measured the length of the block to get know which dip stick to use lol. liana block is longer... Pickups where the same depth... |
|
| Author: | zukenutter [ Mon Nov 24, 2014 9:10 pm ] |
| Post subject: | Re: M series dipstick |
I'll have to check, just assumed the block was the same. Hmm |
|
| Author: | Gromet [ Mon Nov 24, 2014 9:18 pm ] |
| Post subject: | Re: M series dipstick |
nah... I got worried when my mate went to stick the Jimny dipstick in because the 1.5 one was hitting the bottom of my sump. so i but the Jimny tappet cover on and measured from the sump gasket to the dipstick hole... but the extra 500ml you would get from the Jimny dipstick wouldn't hurt it I dont think. |
|
| Author: | prolecs [ Tue Feb 09, 2021 2:50 pm ] |
| Post subject: | Re: M series dipstick |
These crappy dipsticks appear to have a code stamped in the metal just below the plastic bit. My Jimny has 80A (bought as a replacement for M13 Jimny from Mr Suzuki). The conversion to M15 was done b4 my ownership so confirmation from someone with original M13 Jimny would be good. The Swifts etc may all be different as well. M18 Liana has 69G and is a bit longer with full/low markings somewhat different as well. Attachment: 20210209_144216 (Small).jpg Attachment: 20210209_144317 (Small) (1).jpg Attachment: 20210209_144301 (Small).jpg
|
|
| Author: | prolecs [ Tue Feb 09, 2021 3:09 pm ] |
| Post subject: | Re: M series dipstick |
It turns out the stamped code is part of the genuine part number !!! So 80A is Jimny M13 and 69G is M18 Liana |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|