auszookers.com
http://auszookers.com/forum/

can anyone make me something like this (sierra rear bar)
http://auszookers.com/forum/viewtopic.php?f=8&t=9564		 Page 1 of 3
Author:  shep [ Mon Feb 01, 2010 2:45 am ]
Post subject:  can anyone make me something like this (sierra rear bar)
http://lowrangeoffroad.com/images/samur ... zortc2.jpg

the cost of freight from seppoland is a bit prohibitive so is there anyone in oz how could do
a proper job on a rear bumper/tow bar/ tyre holder?
Author:  joeblow [ Mon Feb 01, 2010 2:51 am ]
Post subject:  Re: can anyone make me something like this
what are they asking for that one?
Author:  89_tintop [ Mon Feb 01, 2010 2:57 am ]
Post subject:  Re: can anyone make me something like this
I'll place my order now aswell..

That is one good looking rear bar.
Author:  appsie [ Mon Feb 01, 2010 2:57 am ]
Post subject:  Re: can anyone make me something like this
have always wanted to build a bumper like the ones on lowrange.definately look the goods
Author:  joeblow [ Mon Feb 01, 2010 3:03 am ]
Post subject:  Re: can anyone make me something like this
well, if enough people are keen i might be able to come up with a game plan.
Author:  foolsp33d [ Mon Feb 01, 2010 3:03 am ]
Post subject:  Re: can anyone make me something like this
another taker here Mr Joe.... swap ya for a brand new dishwasher!>?
Author:  Chop [ Mon Feb 01, 2010 3:10 am ]
Post subject:  Re: can anyone make me something like this
yeah i'd pay someone locally for one like that :wink:

Chop
Author:  joeblow [ Mon Feb 01, 2010 3:12 am ]
Post subject:  Re: can anyone make me something like this
foolsp33d wrote:
another taker here Mr Joe.... swap ya for a brand new dishwasher!>?


haha...whats her name? :wink:


seriously, i built one many years ago that was a 'zook' version of a kaymar. a lot of work to be done right.

there are two styles i can do, one is kaymar and the other...well...i'll put some pics up tommorow.
Author:  shep [ Mon Feb 01, 2010 3:12 am ]
Post subject:  Re: can anyone make me something like this
joeblow wrote:
what are they asking for that one?


$250us for the bumper
$220us for the tyre holder
and you would have to think $500us for freight.

i would like one that takes the narva adr approved taillights.
the ones with the reverse light http://www.repcotrade.com.au/images/Sta ... %20sml.jpg
Author:  morpheus [ Mon Feb 01, 2010 4:16 am ]
Post subject:  Re: can anyone make me something like this
that is a HOT looking bumper, i'd buy that, THEN buy a sierra just for something to display it on :-)
Author:  Polar_Bear [ Mon Feb 01, 2010 4:53 am ]
Post subject:  Re: can anyone make me something like this
sierra only?.. what about one for vits? 8)
Author:  shandy92 [ Mon Feb 01, 2010 5:15 am ]
Post subject:  Re: can anyone make me something like this
if you want to make one for the vitara, ill get one for sure and im sure there are others that would like something to replace there standard plastic bumbers as well.

Mitch
Author:  v.w.dave [ Mon Feb 01, 2010 6:40 am ]
Post subject:  Re: can anyone make me something like this
Hey Joe and shep. If you find out how much it would cost to get it shipped to 75080 Richardson Texas (That is where my father lives) or to 76643 Hewitt Texas (thats where my sister lives) what ever one is cheaper. I can have my family ship it over here a lot cheaper. I do it for mates all the time on large things like this. If you can get one over here then you can copy it. Just a thought. They can get it shipped for about a third the price.

PM me if you want to know the exact address

oh and its funny the lic. plate on that zook is from texas you can see the cowboy in the center on the bottom in blue.
Author:  v.w.dave [ Mon Feb 01, 2010 6:50 am ]
Post subject:  Re: can anyone make me something like this
If you look close it looks like the bumper raps under and is a bash plate for fuel tank.
Author:  atari4x4 [ Mon Feb 01, 2010 2:05 pm ]
Post subject:  Re: can anyone make me something like this
Polar_Bear wrote:
sierra only?.. what about one for vits? 8)


x 4 for the SV420 Vitara's

Stuey, mike.knew, ninjamoses & myself... would be very interested along with a cradle to adapt an ARB winchbar... 8)
Author:  joeblow [ Mon Feb 01, 2010 3:53 pm ]
Post subject:  Re: can anyone make me something like this
atari4x4 wrote:
would be very interested along with a cradle to adapt an ARB winchbar... 8)


just waiting on a decision from the powers that be. :wink:
Author:  Joe [ Mon Feb 01, 2010 3:56 pm ]
Post subject:  Re: can anyone make me something like this
shandy92 wrote:
if you want to make one for the vitara, ill get one for sure and im sure there are others that would like something to replace there standard plastic bumbers as well.

Mitch


x2 :P
Author:  atari4x4 [ Mon Feb 01, 2010 4:31 pm ]
Post subject:  Re: can anyone make me something like this
joeblow wrote:
atari4x4 wrote:
would be very interested along with a cradle to adapt an ARB winchbar... 8)


just waiting on a decision from the powers that be. :wink:


wicked, can i be the test monkey? :D
Author:  Fatzook [ Tue Feb 02, 2010 12:03 am ]
Post subject:  Re: can anyone make me something like this
atari4x4 wrote:
Polar_Bear wrote:
sierra only?.. what about one for vits? 8)


x 4 for the SV420 Vitara's

Stuey, mike.knew, ninjamoses & myself... would be very interested along with a cradle to adapt an ARB winchbar... 8)


Wouldn't the SV420 rear bar be the same as the 1.6? If so, I have a vit I can start modeling a bar off of. I'm just a little time poor at the moment trying to get a few other products off the ground.

Pete
Author:  atari4x4 [ Tue Feb 02, 2010 1:57 am ]
Post subject:  Re: can anyone make me something like this
Fatzook wrote:
atari4x4 wrote:
Polar_Bear wrote:
sierra only?.. what about one for vits? 8)


x 4 for the SV420 Vitara's

Stuey, mike.knew, ninjamoses & myself... would be very interested along with a cradle to adapt an ARB winchbar... 8)


Wouldn't the SV420 rear bar be the same as the 1.6? If so, I have a vit I can start modeling a bar off of. I'm just a little time poor at the moment trying to get a few other products off the ground.

Pete


Hey Pete,

The front & rear of the SV420's are VERY different to the early vitara's, i'll try & find some photo's to compare the 2. There is a massive amount of formed & pressed steel in the rear of the SV's where the 1.6's have a simple tube crossmember.
Author:  nandor85 [ Tue Feb 02, 2010 2:03 am ]
Post subject:  Re: can anyone make me something like this
well i could play round and see what i could come up with i had my front bumper u want to find out what thickness of steel they be using should be able to make them up to 3mm thick
Author:  mcwilly [ Tue Feb 02, 2010 11:53 am ]
Post subject:  Re: can anyone make me something like this
I'd be keen for a sierra rear. Would it work with a tow bar?
Author:  shep [ Tue Feb 02, 2010 12:23 pm ]
Post subject:  Re: can anyone make me something like this (sierra rear bar)
mcwilly wrote:
I'd be keen for a sierra rear. Would it work with a tow bar?


i want it to be the tow bar.
looks like the cost from lowrange is approximately $2000USD delivered, i haven't
bothered with ZOR as they don't seem to like dealing outside the us and
i am waiting for locktup to get back to me.
Author:  ninjamoses [ Tue Feb 02, 2010 4:20 pm ]
Post subject:  Re: can anyone make me something like this (sierra rear bar)
Just posting to confirm Atari's thoughts, I would definitely be interested in one also for a SV420 Vit (and a front bar!). Strangely enough, a SV420 Vit has appeared over the road from me with an ARB bar on it. Might have to go investigate.

EDIT: Should have mentioned, if front bars do get made for a SV420 Vit would much prefer it to be based off the Shrockworks one (which is now discontinued) then an ARB. Shrockworks jobby is much cleaner/closer hugging.

http://lowrangeoffroad.com/images/sidek ... kfront.jpg

cheers,
Moses
Author:  steve [ Tue Feb 02, 2010 4:24 pm ]
Post subject:  Re: can anyone make me something like this (sierra rear bar)
I might make one too, everyone will have one, except shep :lol:
Author:  atari4x4 [ Tue Feb 02, 2010 4:27 pm ]
Post subject:  Re: can anyone make me something like this (sierra rear bar)
ninjamoses wrote:
Just posting to confirm Atari's thoughts, I would definitely be interested in one also for a SV420 Vit (and a front bar!). Strangely enough, a SV420 Vit has appeared over the road from me with an ARB bar on it. Might have to go investigate.


on ya bike... I want photos 8)
Author:  Joe [ Tue Feb 02, 2010 6:51 pm ]
Post subject:  Re: can anyone make me something like this
Fatzook wrote:
atari4x4 wrote:
Polar_Bear wrote:
sierra only?.. what about one for vits? 8)


x 4 for the SV420 Vitara's

Stuey, mike.knew, ninjamoses & myself... would be very interested along with a cradle to adapt an ARB winchbar... 8)


Wouldn't the SV420 rear bar be the same as the 1.6? If so, I have a vit I can start modeling a bar off of. I'm just a little time poor at the moment trying to get a few other products off the ground.

Pete


Id be interested in one for a 1.6 vit :please:
Author:  shep [ Tue Feb 02, 2010 6:54 pm ]
Post subject:  Re: can anyone make me something like this (sierra rear bar)
steve wrote:
I might make one too, everyone will have one, except shep :lol:


bugger you lot, if no one wants the job i will get one from lowrange. :wink:
Author:  TonkaTuff [ Tue Feb 02, 2010 7:10 pm ]
Post subject:  Re: can anyone make me something like this (sierra rear bar)
Would love to know how this one fits up been mulling over a design for some time but am a little sus on just using the existing tow bar mounts
Author:  steve [ Tue Feb 02, 2010 7:19 pm ]
Post subject:  Re: can anyone make me something like this (sierra rear bar)
shep wrote:
steve wrote:
I might make one too, everyone will have one, except shep :lol:


bugger you lot, if no one wants the job i will get one from lowrange. :wink:


you might be better off, coz it no one here will make it within 2 years :wink:
Page 1 of 3 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/