Author |
Message |
DarkHorse
az supporter
Joined: Wed Apr 14, 2010 11:30 pm Posts: 5414
Vehicle: 08 SV650
|
Posted: Wed Dec 05, 2012 11:33 am |
|
|
|
|
christover1
az supporter
Joined: Tue Jul 15, 2008 11:30 pm Posts: 8203 Location: Melbourne
Vehicle: Pajero 91 NH 3.0 SWB
|
Posted: Wed Dec 05, 2012 7:25 pm |
|
Made a pdf if it helps http://sdrv.ms/TESAjHI found small differences in the instructions that came with the gears, too. But both were a good guide, even though I wandered away from them at times. Found originals on Zukiworld, but seem to be missing now. Glad I saved them.
|
|
|
|
|
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
Posted: Tue Feb 05, 2013 4:52 pm |
|
so i decided to start pulling my case apart, so far i have found it quite easy but now im stuck...
im on picture number 11 Ive done everything before it, but it will not come out.... is there something im missing???
|
|
|
|
|
christover1
az supporter
Joined: Tue Jul 15, 2008 11:30 pm Posts: 8203 Location: Melbourne
Vehicle: Pajero 91 NH 3.0 SWB
|
Posted: Tue Feb 05, 2013 4:59 pm |
|
maybe end is a bit burred, or something sticking, mine fell out easily
|
|
|
|
|
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
Posted: Tue Feb 05, 2013 5:08 pm |
|
it feels the same as if the yoke and pin are still in :/
|
|
|
|
|
christover1
az supporter
Joined: Tue Jul 15, 2008 11:30 pm Posts: 8203 Location: Melbourne
Vehicle: Pajero 91 NH 3.0 SWB
|
Posted: Tue Feb 05, 2013 5:17 pm |
|
maybe you missed a detent ball or spring
|
|
|
|
|
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
Posted: Tue Feb 05, 2013 5:25 pm |
|
got a total 4 balls and springs out? does that seem right :S i checked ill of them :/
|
|
|
|
|
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
Posted: Tue Feb 05, 2013 5:25 pm |
|
got a total 4 balls and springs out? does that seem right :S i checked ill of them :/
|
|
|
|
|
christover1
az supporter
Joined: Tue Jul 15, 2008 11:30 pm Posts: 8203 Location: Melbourne
Vehicle: Pajero 91 NH 3.0 SWB
|
Posted: Tue Feb 05, 2013 5:35 pm |
|
sounds right. try pushing it back in and out, same time as slightly twisting back n forth
|
|
|
|
|
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
Posted: Tue Feb 05, 2013 7:47 pm |
|
|
|
|
christover1
az supporter
Joined: Tue Jul 15, 2008 11:30 pm Posts: 8203 Location: Melbourne
Vehicle: Pajero 91 NH 3.0 SWB
|
Posted: Tue Feb 05, 2013 7:53 pm |
|
Maybe box is still in gear, putting pressure on it? Did you remove stick when in neutral? that could be an issue..maybe
|
|
|
|
|
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
Posted: Tue Feb 05, 2013 8:32 pm |
|
Dunno it was someone else's :/
|
|
|
|
|
christover1
az supporter
Joined: Tue Jul 15, 2008 11:30 pm Posts: 8203 Location: Melbourne
Vehicle: Pajero 91 NH 3.0 SWB
|
Posted: Tue Feb 05, 2013 9:46 pm |
|
take a break, look at it on a fresh day, it may fall out easily next try
|
|
|
|
|
DarkHorse
az supporter
Joined: Wed Apr 14, 2010 11:30 pm Posts: 5414
Vehicle: 08 SV650
|
Posted: Tue Feb 05, 2013 10:22 pm |
|
Mine practically fell out, to the point where I didn't get a chance to mark the alignment 2 switches (only one has a ball) 2 rod locating springs/balls 1 select lever spring/ball Can you get something onto the end of it and give it a tap that way?
|
|
|
|
|
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
Posted: Wed Feb 06, 2013 7:02 am |
|
So i got the 4 balls out, thats fine... Yeah tapped the end and it doesnt budge
mark the alignment?? what do i have to do there? Doesnt say anything on these instructions
|
|
|
|
|
DarkHorse
az supporter
Joined: Wed Apr 14, 2010 11:30 pm Posts: 5414
Vehicle: 08 SV650
|
Posted: Wed Feb 06, 2013 8:41 pm |
|
Nuthin' as it turns out. One of the sets of destructions I had said to mark the gear and collar so they went back in the same way. Either I got ridiculously lucky and fluked it back in the same or it doesn't matter.
Have you got a gear puller you could get onto the shift fork? Weird that it won't slide given that it's designed to... do you know for sure the case was OK when it was removed from the seller's car?
|
|
|
|
|
Samwich
Joined: Thu Jun 07, 2012 2:13 pm Posts: 1125 Location: Canberra
Vehicle: Vit swb 95
|
Posted: Thu Feb 07, 2013 6:49 am |
|
He said it was working..
I got it out, but i had to use a screw driver and hammer to hit it out
And theres no way its just going to "Slide" back in... everything within the case look in good condition and its clean as, But guessing this shaft could be buggered???
|
|
|
|
|
|