[zookster666]

I have been thinking of making a 6 point internal cage but not sure on how to go about the front section
so post some pics of how you went about it where it runs and mounts etc


I already have the rear hoop just unsure how to do tha "A" pillar section

[Dee]

Bent up 2 pieces that run foward to the corner of the windscreen, turn down at an angle to follow windscreen frame, and then bend again between the dash and door to go down to a mounting plate on te floor.

I then bent & notched two spreader pieces, one at the top of the windscreen, one at the base above the dash.

Dunno if you can see but u I also have door bars/braces going from the b pillar (at seat height) down to the base of the 'a pillar' bars.

[Taff]

I always wondered what you did with your seatbelts, thought you went to a 4pt harness or something.

Looks awesome without the B pillar.

[Dee]

Taff wrote:

I always wondered what you did with your seatbelts, thought you went to a 4pt harness or something.

Looks awesome without the B pillar.

cheers yeah that was what i was aimin for with the half doors & all, no b pillar.

[zookster666]

thanks for that mate appreciate it

[Taff]

You might need to dent your doors in a little bit to get the tube through.

Mine is similar to dee's without the cross brace in the roof.

[moose]

Dee , can you take a pic of it going down the dash (a pillar leg)
thanx

[Dee]

I'll try and get one this arv moosey

[Dee]

these ok?

[zookster666]

I started on my cage got both of the a pillar legs in do you have any problems with the doors not closing properly

[Scrawny]

zookster666 wrote:

do you have any problems with the doors not closing properly

Mine needed a bit of encouragement to close.

There was a thread on OL a while ago on cages wasn't there? Does anyone remember it?

[Dee]

yeah u will have probs with door clearance. When i made my half doors i narrowed them at the top/front to clear the cage.

[zookster666]

I finished my cage today and fitted it I'm really happy with it besides the doors being a little
stubborn to shut. And it's not as braced as yours Dee hope I never need it though lol.

[fourby]

Pics zoolster?

[zookster666]

I will post some when the computer is fixed I'm using my
iPhone at the moment

[chef]

so any pic yet???

[zookster666]

will have some this weekend ,mate

[zookster666]

here are pics as promised this is the best i have

[steak_knife]

Nice , now you have to get it plated!!

[Scrawny]

Do you have anything above the windscreen?

[steak_knife]

ScrawnC wrote:

Do you have anything above the windscreen?

Yep have a closer look.

[zookster666]

Yeah there's a bar ontop of the windscreen I made it sit a little hight than it to so if it does go over the windscreen won't break I hope

what do u mean I have to get it plated?

[steak_knife]

Blue plate, Mod plate, If Dot pull you up thay will want to see one.
There are mobile engineer's that have a Qld trans ticket that can plate it for you.

[zookster666]

oh yeah getting that all sorted my boss can do blue plates. I still need to sort out the padding im just waiting for the off cuts of foam that we use on the cages we make. I cant see the point in buying it if were going to throw smaller pieces out.
Ill put pics up when i do that to

[steak_knife]

zookster666 wrote:

oh yeah getting that all sorted my boss can do blue plates. I still need to sort out the padding im just waiting for the off cuts of foam that we use on the cages we make. I cant see the point in buying it if were going to throw smaller pieces out.
Ill put pics up when i do that to

I like you!!!!!!!

[zookster666]

lol i like me to haha

[jimbo_jones]

zookster666 wrote:

lol i like me to haha

the whore likes you

[steak_knife]

jimbo_jones wrote:

zookster666 wrote:

lol i like me to haha

the whore likes you

Your just jealous! peaceout

[zookster666]

Someones gotta like me lol

[steak_knife]

zookster666 wrote:

Someones gotta lick window's with me lol

Fixed it for ya.