nothing car related but here is somthing i made up at work this week. it bolts on to the side of a ship and discharges the waste water from the heat exchanger on the A/C system.
i thought i pull out some good ally welds.
| auszookers.com https://auszookers.com/forum/ |
|
| awesome welds https://auszookers.com/forum/viewtopic.php?f=14&t=23455 |
Page 1 of 9 |
| Author: | Shansh [ Fri Jul 01, 2011 3:58 am ] |
| Post subject: | awesome welds |
there is obviously some gun fabricators on here so after seeing a similar thread on an off road racing forum though AZ must be able to do better than those boys, so anybody who has some pics of some shit hot welding they (or someone else for that matter) has done, I for one would love to see it |
|
| Author: | bails [ Fri Jul 01, 2011 5:34 am ] |
| Post subject: | Re: awesome welds |
nothing car related but here is somthing i made up at work this week. it bolts on to the side of a ship and discharges the waste water from the heat exchanger on the A/C system.
i thought i pull out some good ally welds.
|
|
| Author: | Ridge [ Fri Jul 01, 2011 5:40 am ] |
| Post subject: | Re: awesome welds |
Fatzook did these for me 
|
|
| Author: | Kermy87 [ Fri Jul 01, 2011 5:55 am ] |
| Post subject: | Re: awesome welds |
Here's a canopy I built with a mate a while ago pretty pissed at the time, this is the latch internal,, chook Shit welds with a mig,, see if u can spot the cock up 
Measure twice,, weld once |
|
| Author: | JrZook [ Fri Jul 01, 2011 6:06 am ] |
| Post subject: | Re: awesome welds |
Imma no welder but I thought these looked ok at the time and haven't fallen off yet.  TIG'd
Note the Suzuki factory welds in the 1st and 3rd pic. |
|
| Author: | dano_mung [ Fri Jul 01, 2011 6:21 am ] |
| Post subject: | Re: awesome welds |
Kermy87 wrote: Here's a canopy I built with a mate a while ago pretty pissed at the time, this is the latch internal,, chook Shit welds with a mig,, see if u can spot the cock up
Measure twice,, weld once Ah is the latch stop on the wrong side and now won't allow the latch to open? 
|
|
| Author: | Kermy87 [ Fri Jul 01, 2011 6:45 am ] |
| Post subject: | Re: awesome welds |
dano_mung wrote: Kermy87 wrote: Here's a canopy I built with a mate a while ago pretty pissed at the time, this is the latch internal,, chook Shit welds with a mig,, see if u can spot the cock up Measure twice,, weld once Ah is the latch stop on the wrong side and now won't allow the latch to open? It was meant to be the spacer under the latch |
|
| Author: | shep [ Fri Jul 01, 2011 6:56 am ] |
| Post subject: | Re: awesome welds |
bails wrote: nothing car related but here is somthing i made up at work this week. it bolts on to the side of a ship and discharges the waste water from the heat exchanger on the A/C system.
i thought i pull out some good ally welds. hay bails. do you work for pirkins? |
|
| Author: | monley [ Fri Jul 01, 2011 7:21 am ] |
| Post subject: | Re: awesome welds |
 Dam it! I knew i should have taken a pic of the full pen weld i did at work the other day with flux core 
Some nice welds in the pics above to
|
|
| Author: | alien [ Fri Jul 01, 2011 8:40 am ] |
| Post subject: | Re: awesome welds |
These are done by Brian at suzistore: 
|
|
| Author: | andrew88 [ Fri Jul 01, 2011 9:21 am ] |
| Post subject: | Re: awesome welds |
ally tig, 3mm rhs to 2mm end plate. 
ally mig, 3 passes, 20mm base plate to 6mm extrusion ( do this at work every day) |
|
| Author: | mnemonix [ Fri Jul 01, 2011 9:33 am ] |
| Post subject: | Re: awesome welds |
Andrew88: in the ally mig photo, do you use pulse mode? Just looks like each "dime" has a cool spot in the centre. What action do you use with the torch/gun? ie: cursive "e's" etc. |
|
| Author: | joeblow [ Fri Jul 01, 2011 10:05 am ] |
| Post subject: | Re: awesome welds |
alien wrote: These are done by Brian at suzistore:
naughty naughty............who needs a visible chassis number eh? |
|
| Author: | andrew88 [ Fri Jul 01, 2011 11:11 am ] |
| Post subject: | Re: awesome welds |
mnemonix wrote: Andrew88:
in the ally mig photo, do you use pulse mode? Just looks like each "dime" has a cool spot in the centre. What action do you use with the torch/gun? ie: cursive "e's" etc. Pritty sure the welder isn't set up for pulse. I do circle's to get that affect (which may be cursive e's now that i think about it). Apart of my procedure is to heat the base plate to 200 degrees with a oxy, then weld straight away. I was getting too much undercut with other methods i tryed. I've been approved for this procedure by engineer. |
|
| Author: | monley [ Fri Jul 01, 2011 11:14 am ] |
| Post subject: | Re: awesome welds |
Andrew88: Any pics of welding ally with the old TIG? Nice welding BTW! |
|
| Author: | bails [ Fri Jul 01, 2011 12:04 pm ] |
| Post subject: | Re: awesome welds |
shep wrote: hay bails. do you work for pirkins? no. work for the defence. |
|
| Author: | alien [ Fri Jul 01, 2011 1:11 pm ] |
| Post subject: | Re: awesome welds |
joeblow wrote: alien wrote: These are done by Brian at suzistore: naughty naughty............who needs a visible chassis number eh? the first bit is all the same anyway =P haha |
|
| Author: | atari4x4 [ Fri Jul 01, 2011 1:27 pm ] |
| Post subject: | Re: awesome welds |
|
|
| Author: | andrew88 [ Fri Jul 01, 2011 8:41 pm ] |
| Post subject: | Re: awesome welds |
monkey wrote: Andrew88: Any pics of welding ally with the old TIG? Nice welding BTW!
cheers. the top pic is ally tig and bottom is ally mig. |
|
| Author: | PJ.zook [ Fri Jul 01, 2011 9:33 pm ] |
| Post subject: | Re: awesome welds |
Will have to post pictures of a supposed 'professional' workshop whom outfit the interiors of work vans, utes etc... with shelving, workbenches and the like. The job they did on my new van, migod a chimpanzee would be disgusted at the quality of the job, the welds look like they just had a bird shit directly on the joins, then painted over it, and that's just the beginning. |
|
| Author: | want33s [ Fri Jul 01, 2011 9:53 pm ] |
| Post subject: | Re: awesome welds |
Feraltech TIG welding on my rear lower arm brackets. 
|
|
| Author: | jonno_racing [ Sat Jul 02, 2011 4:52 am ] |
| Post subject: | Re: awesome welds |
i love looking at fab work and then looking at the original suzuki welds... so much over kill |
|
| Author: | joeblow [ Sat Jul 02, 2011 7:10 am ] |
| Post subject: | Re: awesome welds |
Wing welds on the JML Sierra bar.... 
|
|
| Author: | 3cyl [ Sat Jul 02, 2011 7:17 am ] |
| Post subject: | Re: awesome welds |
That's art! |
|
| Author: | Rusho [ Sat Jul 02, 2011 7:55 am ] |
| Post subject: | Re: awesome welds |
joeblow wrote: Wing welds on the JML Sierra bar....
Not bad 
|
|
| Author: | monley [ Sat Jul 02, 2011 8:07 am ] |
| Post subject: | Re: awesome welds |
3cyl wrote: That's art!
x2 |
|
| Author: | atari4x4 [ Sat Jul 02, 2011 8:09 am ] |
| Post subject: | Re: awesome welds |
show off 
|
|
| Author: | Shansh [ Sat Jul 02, 2011 12:26 pm ] |
| Post subject: | Re: awesome welds |
love it, boobs in one thread, sexy welding in another thread, keep em coming boys (and girls), i am a shithouse welder, hence I love looking at work people who know wtf they are doing have done |
|
| Author: | ZookiMonsta [ Sun Jul 03, 2011 7:48 am ] |
| Post subject: | Re: awesome welds |
The sexiest welds I've seen (not done by me)
|
|
| Author: | ZookiMonsta [ Sun Jul 03, 2011 8:26 am ] |
| Post subject: | Re: awesome welds |
Rusho wrote: What is it from Corey??
All done by Camburg OffRoad in the states, rear diff and roll cage in one of their trophy trucks... don't know much more info than that |
|
| Page 1 of 9 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|