| auszookers.com https://www.auszookers.com/forum/ |
|
| Transfer case shifter fitting tool https://www.auszookers.com/forum/viewtopic.php?f=14&t=2969 |
Page 1 of 1 |
| Author: | Damo [ Wed Sep 17, 2008 2:07 am ] |
| Post subject: | Transfer case shifter fitting tool |
Ever tried getting the transfer case shifter out. It can be a prick of a job. I was having a bastard time getting mine back in today so made this. 
It is a little flimsy so it bends a bit when putting pressure on the locking ring. I just need to tack weld the cuts where the bends are, once i've done that it should be good. |
|
| Author: | Scrawny [ Wed Sep 17, 2008 2:10 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
Very flash!! 
I think you have too much time on your hands 
|
|
| Author: | royce [ Wed Sep 17, 2008 2:12 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
you could sell them!!! |
|
| Author: | Damo [ Wed Sep 17, 2008 2:19 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
ScrawnC wrote: Very flash!!
I think you have too much time on your hands Took me 10 mins  the metal was a pice of scrap (the sides were folded like that), I just used a step drill for the big hole, a hacksaw and pair of pliers.
|
|
| Author: | gregt [ Wed Sep 17, 2008 2:57 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
i could have done with one of those on the weekend laying under car pulling the cap down while son turned it with screw driver pian in the #$%^ 
|
|
| Author: | just_cruizin [ Mon Sep 22, 2008 1:32 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
never thought about doing one in the vehicle. Suppose having 4 transfer cases lying around I just pull the whole thing out |
|
| Author: | Damo [ Mon Sep 22, 2008 11:48 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
just_cruizin wrote: never thought about doing one in the vehicle. Suppose having 4 transfer cases lying around I just pull the whole thing out
I usually pull the shifter out so getting it back in the car is easier. Having the roctoy ring on it made it really difficult to fit, so much so that I am going to have a look at modifying it or the tunnel to make working on it easier. |
|
| Author: | lukes_89 [ Mon Jun 14, 2010 6:54 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
thats an awesome idea allot of people could do with these lately. |
|
| Author: | appsie [ Tue Jun 15, 2010 9:06 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
it does suck pulling the case in and out with roctoy ring. Cool idea man
|
|
| Author: | 31zook [ Wed Jun 16, 2010 8:05 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
am i the only one who pulls the Tcase out everytime with rockring and stick? |
|
| Author: | crazynic [ Wed Jun 23, 2010 11:17 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
Ummmm.... What may i ask is wrong with two screw drivers? I have even managed on the side of a track to unscrew the shift boot screws with the ignition key and remove the transfer shifter by hand and use the jack handle to get a stuck transfer out of neutral..... Are you bored or just a soft cock? 
|
|
| Author: | lukes_89 [ Wed Jun 23, 2010 11:43 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
you must have a good case then crazynic becqause mine was an utter bitch to get out and back in. |
|
| Author: | want33s [ Wed Jun 23, 2010 11:48 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
lukes_89 wrote: you must have a good case then crazynic becqause mine was an utter bitch to get out and back in.
Two screwdrivers has worked for me plenty of times....... but the tool Damo made would work a lot easier. |
|
| Author: | Fatzook [ Wed Jun 23, 2010 1:00 pm ] |
| Post subject: | Re: Transfer case shifter fitting tool |
want33s wrote: lukes_89 wrote: you must have a good case then crazynic becqause mine was an utter bitch to get out and back in. Two screwdrivers has worked for me plenty of times....... but the tool Damo made would work a lot easier. Where is Damo these days ?.... |
|
| Author: | JrZook [ Thu Jun 24, 2010 12:03 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
Fatzook wrote: want33s wrote: lukes_89 wrote: you must have a good case then crazynic becqause mine was an utter bitch to get out and back in. Two screwdrivers has worked for me plenty of times....... but the tool Damo made would work a lot easier. Where is Damo these days ?.... This is a goooooood question! Maybe steaky fought him to get his AFM back
|
|
| Author: | Gonzo [ Sat Jun 26, 2010 12:51 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
Are Vitara's different ?? I found it eay to get out Simply back off retainer bolts and push and turn with old rag !!
|
|
| Author: | zot_boy [ Sun Jun 27, 2010 11:37 am ] |
| Post subject: | Re: Transfer case shifter fitting tool |
vitaras are newer and have grease in them still haha i think every sierra should have come with one of these in the glove box
|
|
| Author: | Fatzook [ Sun Jun 27, 2010 12:26 pm ] |
| Post subject: | Re: Transfer case shifter fitting tool |
I'll have some laser cut ones ready in a few weeks. Put the CAD files in tonight for cutting. 
|
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|