Zook_Fan wrote:
C:\Awesome Porn????? maybe you should check your pics before uploading aye?
| auszookers.com https://auszookers.com/forum/ |
|
| Winch bar https://auszookers.com/forum/viewtopic.php?f=14&t=3465 |
Page 1 of 1 |
| Author: | esky [ Wed Dec 03, 2008 3:53 am ] |
| Post subject: | Winch bar |
Well my winch bar is almost complete. Just getting primed and ill paint it tomorrow. Basis is 100sq RHS with 10mm 350 grade uprights. Theres a cut out for the which which was gusseted to make up the strength. To say i overengineered this bar is not the whole truth. Now, something that made me think was the pitiful mounting holes on the chassis. my main concern was the minute gap from the holes to the end of the chassis, and the probability of them stretching. I know everyone uses them and I havnt heard any problems except in excessive situations, but being me I made some 3mm brackets that were tig welded onto the chassis for a bit more strength. apart from ripping the chassis further back, im interested to see if these pose any problems. All metal was supllied and cut at work, welding done at work, and total cost is about 16 bucks for bolts. Ill get some photos of it tomorrow, but here is noob, and auto cad. |
|
| Author: | Zook_Fan [ Wed Dec 03, 2008 4:00 am ] |
| Post subject: | Re: Winch bar |
C:\Awesome Porn????? maybe you should check your pics before uploading aye? |
|
| Author: | Mike [ Wed Dec 03, 2008 4:04 am ] |
| Post subject: | Re: Winch bar |
Zook_Fan wrote: C:\Awesome Porn????? maybe you should check your pics before uploading aye?
|
|
| Author: | Mike [ Wed Dec 03, 2008 4:16 am ] |
| Post subject: | Re: Winch bar |
but seriously that bar looks good my bar is starting to pull out of the chassis rail so i was thinking of doing something similar to what your doing are they going to be the only mounting points for the bar? |
|
| Author: | Damo [ Wed Dec 03, 2008 10:09 am ] |
| Post subject: | Re: Winch bar |
Zook_Fan wrote: C:\Awesome Porn????? maybe you should check your pics before uploading aye?
I think plating the chassis is a pretty good idea esky. |
|
| Author: | royce [ Wed Dec 03, 2008 12:11 pm ] |
| Post subject: | Re: Winch bar |
my vit ARB bar has plates that clamp to the crossmember with u bolts, that might be worth a look as well |
|
| Author: | smileysmoke [ Wed Dec 03, 2008 2:28 pm ] |
| Post subject: | Re: Winch bar |
what tubing is the cat made out of? 
you should cut up another few templates up then sell em off! i would be keen as, need a front bar |
|
| Author: | esky [ Thu Dec 04, 2008 1:37 am ] |
| Post subject: | Re: Winch bar |
All porn is awesome, but i didnt think anyone would motice thatfolder so fast. Well I was going to paint my bar tonight but its all installed and the winch is hooked up. Just need two longer bolts, and some brackets for my indicators and its done. Had to trim the bottom of the grill support to squeeze the xinch in, and welding the uprights kind of squeezed them out a bit and I had to shave them to get it to fit. The winch controller plugs in the grill where i cut a small amount out. Apart from cutting the main bar with a 9 inch grinder and pretty much putting everything else out of alighnment, it all went together nicely and tightly. so next time you build something dont forget your local laser cutter. and a wad of cash to get things done. On thing left to do is when i measured everything up I forgot to factor in the clutch handle. thats why there is two holes with no tube. Now everything is in ive seen I can shave an arc in the tube facing rearwards and plate it. It will be tight but everything here is Now im hanging to go use my winch this weekend. oh and cat is 114mm extruded ally |
|
| Author: | jimbo_jones [ Thu Dec 04, 2008 3:13 am ] |
| Post subject: | Re: Winch bar |
sweet how much did the plates cost to make did you wana get some more made up? |
|
| Author: | Fatzook [ Thu Dec 04, 2008 6:55 am ] |
| Post subject: | Re: Winch bar |
Nice fabwork, but if you don't want to get done by transport you should weld some 30mm wide flat bar around the virtical plates on all forward facing edges. This is to protect pedestrians. Also the tube through the top needs to be capped at the ends for the same reasons. Keep up the good work. Pete |
|
| Author: | Rockhopper [ Thu Dec 04, 2008 11:08 am ] |
| Post subject: | Re: Winch bar |
Good work Esky. Fatzook is right and I would probably do those couple of mods so you don't get picked up. As for the Awsome Porn folder, I thought that folder was built into Windows, just like the My Documents folder 
|
|
| Author: | TZAR [ Thu Dec 04, 2008 1:00 pm ] |
| Post subject: | Re: Winch bar |
Mike wrote: are they going to be the only mounting points for the bar?
these 2 holes in the end of the chassis are were the factory winch bolts to. They are strong enough if you follow good engineering practises when making bar work remember that clamping force is what is needed so if you brace in between the insides of the chassis rail so that the steel can pull tight onto something then this where you get your strength. |
|
| Author: | jamhic [ Sat Apr 25, 2009 10:34 pm ] |
| Post subject: | Re: Winch bar |
esky, is your tigerz11 winch the 12,000 or 10,000 lbs? how you find it? |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|