| auszookers.com https://auszookers.com/forum/ |
|
| Sierra tCase into 2008 Jimny https://auszookers.com/forum/viewtopic.php?f=14&t=41879 |
Page 1 of 1 |
| Author: | kyzermattingley [ Sat Jul 13, 2013 12:17 am ] |
| Post subject: | Sierra tCase into 2008 Jimny |
Made up my own brackets for my Jimny to take the Sierra transfer case  Machined out the factory Jimny sensor pick up wheel thing and attached it to the output flange  Picked up a few extra mounting points, all from 5mm plate  Powder coated it all black Mounts the transfer forward 25mm so the Sierra front shaft fits in the rear easier, it also allows more room for the front haft over the gearbox crossmember. The case also sits 20mm higher. Will put up better shots and more info soon Kyzer |
|
| Author: | zukenutter [ Mon Jul 15, 2013 5:13 pm ] |
| Post subject: | Re: Sierra tCase into 2008 Jimny |
Nice work as usual. I can see a new standard for kit choice. Did you consider joining the mounts to make a cradle, as popular with Sierras running very low gears. |
|
| Author: | joel [ Wed Jul 17, 2013 7:43 pm ] |
| Post subject: | Re: Sierra tCase into 2008 Jimny |
great write up mate. |
|
| Author: | kyzermattingley [ Mon Jul 22, 2013 9:34 am ] |
| Post subject: | Re: Sierra tCase into 2008 Jimny |
zukenutter wrote: Nice work as usual. I can see a new standard for kit choice. Did you consider joining the mounts to make a cradle, as popular with Sierras running very low gears. I did but I wanted to get the transfer out without taking the exhaust off which meant taking off the passengers side mount and bracket while in the car. At present I've fitted up this kit to my car and will be driving it soon ATTN: To make them as kits I need another Sierra transfer (blown or Brocken) to put in my jig, as the one I used is now bolted under my Jimny. I am also considering drawing the whole thing up in CAD and just putting it here Kyzer |
|
| Author: | bohuler [ Mon Jul 22, 2013 10:24 am ] |
| Post subject: | Re: Sierra tCase into 2008 Jimny |
Awsome work as usual mate. For the unedumekated like myself benifts of putting a sierra case into a Jimny? Dave |
|
| Author: | atari4x4 [ Mon Jul 22, 2013 10:29 am ] |
| Post subject: | Re: Sierra tCase into 2008 Jimny |
instant reduction gearing + the ability to use sierra transfer gears for more reduction |
|
| Author: | jono165 [ Mon Jul 22, 2013 12:18 pm ] |
| Post subject: | Re: Sierra tCase into 2008 Jimny |
sierra case is also gear driven instead of chain which slips once worn or under high load. |
|
| Author: | Asps91 [ Tue Jul 23, 2013 1:49 pm ] |
| Post subject: | Re: Sierra tCase into 2008 Jimny |
Wow, are you going to reproduce these mounts any time soon. Would prefer to buy local than from ora! |
|
| Author: | kyzermattingley [ Fri Jul 26, 2013 10:10 am ] |
| Post subject: | Re: Sierra tCase into 2008 Jimny |
Asps91 wrote: Wow, are you going to reproduce these mounts any time soon. Would prefer to buy local than from ora! I just need another transfer (if someone has a stuffed one) to put in my jig to trial fit brackets Kyzer |
|
| Author: | Asps91 [ Fri Jul 26, 2013 11:16 am ] |
| Post subject: | Re: Sierra tCase into 2008 Jimny |
Can't help you there but I'm sure someone here has one lying around that they could donate to a worthy cause! |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|