auszookers.com :: View topic

i can understand what he is talking about, no problems. :wink:

i can understand it itsa just annoying

i might have start new thread teach suzukilwb how to spell

shep wrote:

i can understand what he is talking about, no problems. :wink:

but you are semi illiterate :lol:

make the decision that you have nothing useful to add AND DONT POST

royce wrote:

make the decision that you have nothing useful to add AND DONT POST

Well said Royce. I'm starting to get sick of all this spam. :roll:

NOOBS - Chat section is for chat. If you want to talk shit, keep it out of the tech areas :evil:

even tho i have a cage on mine i am really not a fan of them.But the body was shagged and i thought it would be fun to try make.

Do many people on here daily drive with exos and have cop problems?

Author:	suzukilwb [ Mon Sep 21, 2009 11:35 pm ]
Post subject:	exo cage ideas
i am looking at making a exo cage "ladder rack" i am in SA so i can get away with anything i have put my zook on its side 1 time and my m8 almost did it again last weekend so i think its time to make a cage i just looking for some examples of exo cages on comp trucks or road reg zooks just want to see what other people have done and rough cost i am just fucked with spelling

Author:	brendan [ Mon Sep 21, 2009 11:49 pm ]
Post subject:	Re: exo cage
read your post. then fix it up please

Author:	shep [ Mon Sep 21, 2009 11:55 pm ]
Post subject:	Re: exo cage
i can understand what he is talking about, no problems.

Author:	steak_knife [ Tue Sep 22, 2009 12:00 am ]
Post subject:	Re: exo cage
shep wrote: i can understand what he is talking about, no problems. X2

Author:	ball [ Tue Sep 22, 2009 12:01 am ]
Post subject:	Re: exo cage
shep wrote: i can understand what he is talking about, no problems. but you are semi illiterate

auszookers.com https://auszookers.com/forum/

exo cage ideas https://auszookers.com/forum/viewtopic.php?f=14&t=6777	Page 1 of 3

Author:	brendan [ Tue Sep 22, 2009 12:06 am ]
Post subject:	Re: exo cage
i can understand it itsa just annoying

Author:	suzukilwb [ Tue Sep 22, 2009 12:09 am ]
Post subject:	Re: exo cage
i might have start new thread teach suzukilwb how to spell

Author:	royce [ Tue Sep 22, 2009 12:16 am ]
Post subject:	Re: exo cage
brendan wrote: i can understand it itsa just annoying If you are going to waste a post whinging about spelling you can either A. make sure you never ever make a mistake in any post ever again, specially the same thread B. Fuck off back to the hole you came from C. Front up for your own forum and make whatever rules suits you until then if you dont understand a post make the decision that you have nothing useful to add AND DONT POST

Author:	steak_knife [ Tue Sep 22, 2009 12:16 am ]
Post subject:	Re: exo cage
suzukilwb wrote: i might have start new thread teach suzukilwb how to spell yoor spallink finne maete, farck um!!!

Author:	joeblow [ Tue Sep 22, 2009 12:22 am ]
Post subject:	Re: exo cage ideas
google 'exo cage' for images.

Author:	shep [ Tue Sep 22, 2009 12:24 am ]
Post subject:	Re: exo cage
ball wrote: shep wrote: i can understand what he is talking about, no problems. but you are semi illiterate exactly.

Author:	CairnsZook [ Tue Sep 22, 2009 12:25 am ]
Post subject:	Re: exo cage
royce wrote: make the decision that you have nothing useful to add AND DONT POST Well said Royce. I'm starting to get sick of all this spam. NOOBS - Chat section is for chat. If you want to talk shit, keep it out of the tech areas

Author:	shep [ Tue Sep 22, 2009 12:28 am ]
Post subject:	Re: exo cage
CairnsZook wrote: royce wrote: make the decision that you have nothing useful to add AND DONT POST Well said Royce. I'm starting to get sick of all this spam. NOOBS - Chat section is for chat. If you want to talk shit, keep it out of the tech areas oh are you a mod now are ya.

Author:	CairnsZook [ Tue Sep 22, 2009 12:30 am ]
Post subject:	Re: exo cage ideas
No, I'm just in a bad mood that's all. I'll get over it eventually

Author:	atari4x4 [ Tue Sep 22, 2009 2:03 am ]
Post subject:	Re: exo cage ideas
2 da spiilling narzies eiat shiat! i think this is a neat example of an rear exo, the front half is internal though.

Author:	appsie [ Tue Sep 22, 2009 2:30 am ]
Post subject:	Re: exo cage ideas
cruch the tube??your spelling is bad haha.do you mean crush the tube?like hand rails etc get done? if so no i wouldnt do it that way myself it doesnt take long to notch it out to suit the pipe and looks nicer,makes the welding easier.i just marked mine at the hight and low points,drew roughly where i wanted to notch it with a texta,made the cuts with a 9 inch then rounded off with a 5 inch.took bugger all time. There is a notching thread on pirate 4x4 i believe for use with a drop saw to help get good angles etc?Hope this helps in some way mate

Author:	appsie [ Tue Sep 22, 2009 2:33 am ]
Post subject:	Re: exo cage ideas
mine is just medium wall nb pipe done on a gas weld bender.Not the best pipe or the best methods of doing so but i wanted to learn to build one so i had a go,will find ya some pics.

Page 1 of 3	All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/

Author:	suzukilwb [ Tue Sep 22, 2009 12:43 am ]
Post subject:	Re: exo cage ideas
have googled it and looked at a lot of them did it befor i posted anything and i was going to ask whats the best way to wend it cruch the tube at the end or is there a way to cut it to fit i am not sure how to do it and make it strong what would be the beast to make it out of

Author:	royce [ Tue Sep 22, 2009 1:04 am ]
Post subject:	Re: exo cage ideas
ok you dont crush it, you notch it, there is a thread on this forum about easy ways to do it for material you want AS1163 C350 CHS, make sure its Cold Drawn CHS not hot rolled ERW, for no other reason than if you wish to compete in any comps this it what you need

Author:	suzukilwb [ Tue Sep 22, 2009 1:16 am ]
Post subject:	Re: exo cage ideas
cheers

Author:	steak_knife [ Tue Sep 22, 2009 1:27 am ]
Post subject:	Re: exo cage ideas
http://www.auszookers.com/index.php?nam ... c&start=75 have a look here..

Author:	S13RR4 [ Tue Sep 22, 2009 1:52 am ]
Post subject:	Re: exo cage ideas
www.pirate4x4.com/foru...p?t=456800 can this be done with a hand saw if im cheap and dogy and dont have a drop saw??? are they just straight down cuts or what?

Author:	shep [ Tue Sep 22, 2009 2:08 am ]
Post subject:	Re: exo cage ideas
hat atari where did you find that? do you have any more photos? that looks like what i want.

Author:	bogfrog [ Tue Sep 22, 2009 2:08 am ]
Post subject:	Re: exo cage ideas
Thats the one I've been lookin' @ lately Atari. I love the rear section still gotta work out how to go around or under the snorkel for the drivers side at the front, just not sure what I want to do there as yet?

Author:	atari4x4 [ Tue Sep 22, 2009 2:12 am ]
Post subject:	Re: exo cage ideas
nah sorry guys, i bogged it off the interweb somewhere...

Author:	atari4x4 [ Tue Sep 22, 2009 2:18 am ]
Post subject:	Re: exo cage ideas
i think these 2 have tooooooo much toobing

Author:	atari4x4 [ Tue Sep 22, 2009 2:33 am ]
Post subject:	Re: exo cage ideas
this is the drop saw tube notching method. don't crush the tube, notch it! http://www.pirate4x4.com/forum/showthread.php?t=456800

Author:	bogfrog [ Tue Sep 22, 2009 2:47 am ]
Post subject:	Re: exo cage ideas
Here's a couple more for ya's:

Author:	appsie [ Tue Sep 22, 2009 2:50 am ]
Post subject:	Re: exo cage ideas
even tho i have a cage on mine i am really not a fan of them.But the body was shagged and i thought it would be fun to try make. Do many people on here daily drive with exos and have cop problems?

Author:	jdk81 [ Tue Sep 22, 2009 3:49 am ]
Post subject:	Re: exo cage ideas
appsie wrote: even tho i have a cage on mine i am really not a fan of them.But the body was shagged and i thought it would be fun to try make. Do many people on here daily drive with exos and have cop problems? I too worry about this, as exo is on my to do list over the next 3-4 months. I would assume, the more it looks like functional roof racks/ladder racks, the less cop attention you will receive.