Yeah if you made any changes to it that would be great ill PM you my details
| auszookers.com https://auszookers.com/forum/ |
|
| GIZ GV Snorkel Hole Size?? https://auszookers.com/forum/viewtopic.php?f=37&t=33290 |
Page 1 of 1 |
| Author: | Sco-tie [ Sat Jun 09, 2012 4:11 pm ] |
| Post subject: | GIZ GV Snorkel Hole Size?? |
What hole saw size is needed of the GIZ snorkel on the GV? Ive emailed than asking for instructions but no reply yet....it is the weekend though lol But i know others on here have done it so what size did you use? Ive measured 70mm for the hole does that sound right? |
|
| Author: | foonji [ Sat Jun 09, 2012 10:49 pm ] |
| Post subject: | Re: GIZ GV Snorkel Hole Size?? |
I am going to be installing mine in the next few days after it's been collecting dust for a while. Any one else got any tips for installing them? any quirky problems I need to watch out for? the template seems rather dodgy... |
|
| Author: | Sco-tie [ Sun Jun 10, 2012 12:03 am ] |
| Post subject: | Re: GIZ GV Snorkel Hole Size?? |
A guy on another forum has a really good instruction guid for it but hasnt noted the hole size. http://nbs4x4club.com/forum/index.php?topic=15084.0 I know its not an AZ post but its a good thread with pics shows very easy step by step But whats the hole size?? |
|
| Author: | foonji [ Sun Jun 10, 2012 8:24 am ] |
| Post subject: | Re: GIZ GV Snorkel Hole Size?? |
On the template bailey gave me, he has written that 65-75mm will work. |
|
| Author: | bailey08 [ Sun Jun 10, 2012 10:26 am ] |
| Post subject: | Re: GIZ GV Snorkel Hole Size?? |
yeah, there were no instructions and the template had half the lines missing or so faint you wouldn't know they were there. one of the 3 bolt holes were slightly out to. I think that template I gave you I fixed it up and wrote some destructions on it. that write up on NBS is brilliant. makes sure you pull the mirror in to... I used the cheapest hole saw from bunnings, it will never cut again but worked the once. |
|
| Author: | foonji [ Sun Jun 10, 2012 6:21 pm ] |
| Post subject: | Re: GIZ GV Snorkel Hole Size?? |
Yeah, you marked it 11mm from where it was shown. made a few photocopies today, so will cut one out and put it over the snorkel to see. I've got a grand vitara badge right where the snorkel goes, so gotta de-badge it and move it back out of the way. |
|
| Author: | Sco-tie [ Mon Jun 11, 2012 12:36 am ] |
| Post subject: | Re: GIZ GV Snorkel Hole Size?? |
Can you upload the template on here so i can suss out the changes? I think i will go with the 70mm nice and even in the middle. and give it a go sometime this week |
|
| Author: | foonji [ Mon Jun 11, 2012 8:43 pm ] |
| Post subject: | Re: GIZ GV Snorkel Hole Size?? |
All went well with the snorkel today - viewtopic.php?f=4&t=23711&p=613795#p613795 I can take a pic of the template and upload it, but i wouldn't use it to print out and use. I can snail mail you a copy if you like. |
|
| Author: | Sco-tie [ Mon Jun 11, 2012 11:33 pm ] |
| Post subject: | Re: GIZ GV Snorkel Hole Size?? |
Yeah if you made any changes to it that would be great ill PM you my details
|
|
| Author: | Built4thrashing [ Mon Jun 18, 2012 8:48 pm ] |
| Post subject: | Re: GIZ GV Snorkel Hole Size?? |
I cut an 80mm hole for the snorkel and drilled 15mm holes for the mounting bolts. Used big washers on the mounting bolts. When drilled out as per plan it was not even close to right. |
|
| Author: | Sco-tie [ Mon Jun 18, 2012 9:04 pm ] |
| Post subject: | Re: GIZ GV Snorkel Hole Size?? |
Yeah foonji sent me some copies of the new aligned holes and im going to drill a 70mm hole and see how it all goes with lots of pics during. How did you get it to fit in the end with the wrong holes? |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|