auszookers.com • View topic

Board index » Talking About Stuff » N00b Talk

Carby G13

Page 1 of 1

[ 11 posts ]

Print view

Previous topic | Next topic

Author

Message

Toppy

Joined: Wed May 08, 2013 7:33 pm
Posts: 16
Vehicle: Suzuki Sierra '90 Wide Track

Posted: Tue May 14, 2013 3:00 pm

Hey guys I have a g13a out of a barina to go into my zook. Will the carby off the 1.3 swift fit onto it?

Sent from my GT-I9300 using Tapatalk 2

want33s

az supporter

Joined: Fri Nov 16, 2007 10:30 pm
Posts: 8135
Location: Sunshine Coast Qld

Posted: Tue May 14, 2013 4:00 pm

Barina and Swift are same so YES a Swift carby will fit a Barina motor.

Toppy

Joined: Wed May 08, 2013 7:33 pm
Posts: 16
Vehicle: Suzuki Sierra '90 Wide Track

Posted: Tue May 14, 2013 5:25 pm

Awesome. Just wanting to check. Cheers

Sent from my GT-I9300 using Tapatalk 2

coily96

az supporter

Joined: Wed May 05, 2010 11:50 am
Posts: 823
Location: Beenleigh
Vehicle: Coil Sierra

Posted: Tue May 14, 2013 9:01 pm

Let us know how you go as a suzuki shop told me their a different carby to the sierra.

want33s

az supporter

Joined: Fri Nov 16, 2007 10:30 pm
Posts: 8135
Location: Sunshine Coast Qld

Posted: Tue May 14, 2013 9:23 pm

coily96 wrote:

Let us know how you go as a suzuki shop told me their a different carby to the sierra.

That is correct.
Barina/Swift carby is different to Sierra. It has a lot more pollution gear on it. Cable setup is different. Air hat is different. Not sure about the mounting bolts.

The OP's question isn't too clear.

Toppy

Joined: Wed May 08, 2013 7:33 pm
Posts: 16
Vehicle: Suzuki Sierra '90 Wide Track

Posted: Wed May 15, 2013 7:52 am

What more do you need to know? I have a G13a motor and I can purchase a carby from a g13ba swift. I was told there is more bits that dont need to be connected but apprently should still work?

Sent from my GT-I9300 using Tapatalk 2

Zook_Fan

az supporter

Joined: Thu Mar 13, 2008 10:30 pm
Posts: 4530
Location: Toowoomba
Vehicle: Maruti and LJ80's

Posted: Wed May 15, 2013 10:19 am

What is the G13a motor going in? If it's the sierra that you have in your profile than you won't want a swift carby. They are overly complicated and have a heap of pollution gear on it. The inlet manifold is different and possibly the mounting bolts as want33s has said. If it's going in a swift or barina than use it, if it's going in a sierra get a sierra carby and inlet manifold.

Toppy

Joined: Wed May 08, 2013 7:33 pm
Posts: 16
Vehicle: Suzuki Sierra '90 Wide Track

Posted: Wed May 15, 2013 1:29 pm

Its going in my zook but it is a motor from a Barina apparently. I got the inlet manifold from the same person selling the carby so I am assuming it should all bolt togethet.

Sent from my GT-I9300 using Tapatalk 2

want33s

az supporter

Joined: Fri Nov 16, 2007 10:30 pm
Posts: 8135
Location: Sunshine Coast Qld

Posted: Wed May 15, 2013 1:42 pm

Don't waste your time trying to fit a Swift/Barina carby to a Sierra manifold or trying to make a FWD manifold work in a RWD car.

fordem

Joined: Mon Apr 19, 2010 11:30 pm
Posts: 2656
Location: Georgetown, Guyana
Vehicle: JB420, APK416, A6G415, A6N415

Posted: Thu May 16, 2013 2:11 am

The FWD intake has the water outlet on the left side if fitted in the original east-west configuration, which translates to the rear of the engine in a north-south installation, the RWD intake has it at the front.

Toppy

Joined: Wed May 08, 2013 7:33 pm
Posts: 16
Vehicle: Suzuki Sierra '90 Wide Track

Posted: Thu May 16, 2013 7:20 am

Turns out I was wrong. The manifold I have is a Sierra one. Cheers guys.

Sent from my GT-I9300 using Tapatalk 2

Page 1 of 1

[ 11 posts ]

Board index » Talking About Stuff » N00b Talk

Who is online

Users browsing this forum: No registered users and 9 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum