Yeah you can pop it out easily but efi pumps normally dont like running dry for too long
| auszookers.com https://auszookers.com/forum/ |
|
| PIERBURG 7.21287.53.0 https://auszookers.com/forum/viewtopic.php?f=37&t=56151 |
Page 1 of 1 |
| Author: | fujitsubo [ Wed Nov 27, 2019 8:43 am ] |
| Post subject: | PIERBURG 7.21287.53.0 |
Hi guys when doing a baleno swap into a seirra i have opted to use my existing sj70 tank paired with a PIERBURG 7.21287.53.0 as my tanks only 5 months old and i dont see myself doing any extreme off road with mega angles. plus i'm a lazy C#$# and its one less thing to have to pull out lol my question is. my mechanic friend was saying i should hook up a LPG Safety switch between the fuel relay and the pump for if the car stalls ?. do you think this is a must ? or can i get away with just running some nice 2 core down to the pump with nothing in between. |
|
| Author: | fordem [ Wed Nov 27, 2019 10:30 am ] |
| Post subject: | Re: PIERBURG 7.21287.53.0 |
IF you're using a standard Baleno ECU to run the engine and controlling the fuel pump from that, it's not necessary - the ECU will shut the pump off if the engine stops. |
|
| Author: | fujitsubo [ Wed Nov 27, 2019 1:50 pm ] |
| Post subject: | Re: PIERBURG 7.21287.53.0 |
fordem wrote: IF you're using a standard Baleno ECU to run the engine and controlling the fuel pump from that, it's not necessary - the ECU will shut the pump off if the engine stops. awesome thank you sir, i will just run the 2 core down to the pump, thank you. |
|
| Author: | MrRocky [ Wed Nov 27, 2019 1:50 pm ] |
| Post subject: | Re: PIERBURG 7.21287.53.0 |
Fat pink wire out the baleno harness handles the power to the fuel pump via the relay in the fuse box. Initially when ignition is switched to on position you should hear fuel pump prime for 4 secs then shutoff until car is started. |
|
| Author: | fujitsubo [ Wed Nov 27, 2019 3:02 pm ] |
| Post subject: | Re: PIERBURG 7.21287.53.0 |
MrRocky wrote: Fat pink wire out the baleno harness handles the power to the fuel pump via the relay in the fuse box. Initially when ignition is switched to on position you should hear fuel pump prime for 4 secs then shutoff until car is started. yeah i had some guy cut down my engine loom into a nice small one with just everything it needs to run on it with all the labels and inline fuses so should be all good. one more silly question for you mr rocky. the instructions for this pump came in German hahah can i guess that side of the pump with the neg and pos connections is the outlet to the fuel rail up to the filter and the motor and the larger side of the pump is the inlet from the tank ? |
|
| Author: | MrRocky [ Wed Nov 27, 2019 9:42 pm ] |
| Post subject: | Re: PIERBURG 7.21287.53.0 |
Good question, buggered if i can remember haha I thought there was an arrow on the pump perhaps ? Might be time for google translate. Remember to make sure your tank is clean or the internal mesh filter on the pump will clog |
|
| Author: | bumstein [ Wed Nov 27, 2019 11:55 pm ] |
| Post subject: | Re: PIERBURG 7.21287.53.0 |
MrRocky wrote: Remember to make sure your tank is clean or the internal mesh filter on the pump will clog Out of curiosity, is the mesh filter accessible to clean it if required? |
|
| Author: | MrRocky [ Thu Nov 28, 2019 7:33 am ] |
| Post subject: | Re: PIERBURG 7.21287.53.0 |
Yeah you can pop it out easily but efi pumps normally dont like running dry for too long
|
|
| Author: | fujitsubo [ Thu Nov 28, 2019 10:41 am ] |
| Post subject: | Re: PIERBURG 7.21287.53.0 |
MrRocky wrote: Good question, buggered if i can remember haha I thought there was an arrow on the pump perhaps ? Might be time for google translate. Remember to make sure your tank is clean or the internal mesh filter on the pump will clog from what i can see on this pump the large end has a filter inside it and the small end with the neg and pos terminals is a smaller barb has no filter visible so this to be would translate to large barb to tank small barb next to terminals is up to engine bumstein wrote: MrRocky wrote: Remember to make sure your tank is clean or the internal mesh filter on the pump will clog Out of curiosity, is the mesh filter accessible to clean it if required? on this one the filter does look like its pops out to be flushed or replaced most defs |
|
| Author: | MrRocky [ Thu Nov 28, 2019 6:10 pm ] |
| Post subject: | Re: PIERBURG 7.21287.53.0 |
I normally also use a diahatsu feroza fuel pump bracket to mount the pump to the chassis. It rubber mounts the pump and is the perfect size |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|