oxygenthief wrote:
try connecting the battery
well it turns over so it wont be that
| auszookers.com https://auszookers.com/forum/ |
|
| HELP!! car wont start after puttin it back together https://auszookers.com/forum/viewtopic.php?f=5&t=10977 |
Page 1 of 1 |
| Author: | morpheus [ Thu Apr 08, 2010 11:51 pm ] |
| Post subject: | HELP!! car wont start after puttin it back together |
ok, me and my house mate pulled my G16A vitara apart, i had a cracked head. sent it away, welded, straitened, machined.. we've put it back together and it wont bloody start. new leads, plugs, cap, rotor. VRS kit, everything seems lined up, timing seems ok. makes no shitty noises when it turns over, sparks @ the plug and has compression.. what more can we check for?? any ideas welcome.. |
|
| Author: | PJ.zook [ Thu Apr 08, 2010 11:56 pm ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
Is the G16A injected? I cant remember, if so maybe a sensor is disconnected, not getting power to fuel pump, etc... it could be a million things. About timing too, did you set the timing up 180deg out, it does matter. |
|
| Author: | Fluffy [ Fri Apr 09, 2010 12:00 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
might be out of time.. you might be on the wrong revolution.. 180 degrees out.? |
|
| Author: | alex [ Fri Apr 09, 2010 12:00 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
your compression may be on cylinder 4 and not cylinder 1? |
|
| Author: | want33s [ Fri Apr 09, 2010 12:01 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
G16A is carby... Sounds like you have one of two things wrong.. 1, Cam - crank timing is incorrect. 2, Distributor timing is incorrect. |
|
| Author: | stockman [ Fri Apr 09, 2010 12:09 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
try connecting the battery |
|
| Author: | alex [ Fri Apr 09, 2010 12:11 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
oxygenthief wrote: try connecting the battery
well it turns over so it wont be that
|
|
| Author: | stockman [ Fri Apr 09, 2010 12:13 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
|
|
| Author: | morpheus [ Fri Apr 09, 2010 12:21 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
timing not 180 out, made sure the belt hasn't jumped a tooth, i think after tea were gonna do a full compression test and maybe take the top cover off and have a look inside.. tis annoying, i just wanna drive the bloody thing. |
|
| Author: | Rusho [ Fri Apr 09, 2010 12:25 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
morpheus wrote: timing not 180 out
Try it for shits and giggles, can't hurt
|
|
| Author: | stockman [ Fri Apr 09, 2010 12:25 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
have you checked your getting fuel? |
|
| Author: | morpheus [ Fri Apr 09, 2010 12:34 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
yeah gettin fuel, how much compression should it have each cylinder?? |
|
| Author: | Rusho [ Fri Apr 09, 2010 12:43 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
I THINK its around 120-140psi??? Don't hold me to it, i'm probably wrong. As long as there isn't a great deal of difference betweeen the 4 it should be ok |
|
| Author: | royce [ Fri Apr 09, 2010 12:44 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
ok how do you know the timing is correct? how do you know there is fuel in the carb? how did you time the cam, both keyways up like every other engine or the cam keyway down like a G16 should be
|
|
| Author: | Scrawny [ Fri Apr 09, 2010 12:44 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
Rusho81 wrote: I THINK its around 120-140psi??? Don't hold me to it, i'm probably wrong. As long as there isn't a great deal of difference betweeen the 4 it should be ok
Yep, that'll do |
|
| Author: | MART [ Fri Apr 09, 2010 12:45 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
So while cranking the motor and rotating the dizy 360 degrees , bolt removed and holding down , you get no firing at all , that would mean the timing is out or it is flooded when in the right position and not able to fire , Cheers Paul. |
|
| Author: | morpheus [ Fri Apr 09, 2010 1:25 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
out of curiosity, the rear cam seal, does it look like the front cam seal or is it an o-ring?? |
|
| Author: | stockman [ Fri Apr 09, 2010 6:35 pm ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
Did you work out what it was yet? |
|
| Author: | morpheus [ Sat Apr 10, 2010 7:48 pm ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
yeah i got the thing running... finally.... although a lot of oil is coming out the back of the top of the motor somewhere. i fear maybe the rear cam seal has not gone is?? problem is, we didn't pull them out, the boys @ the head repair place did, so we dont know what were looking for...... and in the VRS kit i have a rubber ring, perhaps 4-5cm round with a wall thickness of maybe 3mm... and its orange.. should that be on the back of the cam?? everything in the VRS kit has been used, apart from this bloody orange ring.. |
|
| Author: | Rusho [ Sat Apr 10, 2010 8:43 pm ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
What was wrong with it?? |
|
| Author: | morpheus [ Sat Apr 10, 2010 10:37 pm ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
i dont know, i got home and looked @ it myself (my mechanic friend was doin all the work) took my time, called someone i know is VERY good with cars, followed his instructions EG, take rocker cover off, make sure the valves lift @ the right time when piston 1 in TDC, make sure the dizzy is on the right cyliner. make sure the leads go to the right plug, i played with the distributor position a little, and it started..... needed a gut full of throttle though, but it started.... and i eventually got it to run without my foot on the pedal, then was able to set the timing........ so. my "mechanic" house mate couldn't get it started.. im a computer nerd.. hate gettin my hands dirty, and with some instructions.. i got it started... in saying that, i would no way have been able to put all the bits back together like he did.. lol |
|
| Author: | morpheus [ Sun Apr 11, 2010 1:59 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
so no one can tell me what the rear cam seal looks like?? |
|
| Author: | MART [ Sun Apr 11, 2010 3:37 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
Do you have a 90 degree dizzy drive , if so the cam seal should be a O ring , does it bolt on with 3 bolts , Cheers Paul. |
|
| Author: | morpheus [ Sun Apr 11, 2010 9:00 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
yeah bolts on with 3 bolts, and i remember putting a thin o-ring in a groove on that part.. but its still leaking oil REALLY bad from the back somewhere.. |
|
| Author: | Rusho [ Sun Apr 11, 2010 11:32 am ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
Gasket around the housing of the dizzy drive, or rocker cover |
|
| Author: | morpheus [ Sun Apr 11, 2010 3:41 pm ] |
| Post subject: | Re: HELP!! car wont start after puttin it back together |
both new, and seems to be more dizzy area, maybe the seal moved when we put it on the head. but its leaking heaps.. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|