auszookers.com
https://auszookers.com/forum/

Can someone cut the fat from my 1.6 wiring loom?
https://auszookers.com/forum/viewtopic.php?f=5&t=12262		 Page 1 of 1
Author:  Red_October [ Fri May 28, 2010 9:26 am ]
Post subject:  Can someone cut the fat from my 1.6 wiring loom?
I'm really not overly confident with this sort of stuff. I was wondering if there was anyone on here that has experience with cutting the fat from a 1.6 harness so that it is as close as possible to plug-and-play and if so, could someone do mine for me? I'd also need the plugs and stray wires labelled too. I will pay for your services :P

Also, am I right in presuming that I just hang on to the wiring behind the dash and in the engine bay and nothing from the front seats back?

Cheers,
Jimmy
Author:  joeblow [ Fri May 28, 2010 10:57 am ]
Post subject:  Re: Can someone cut the fat from my 1.6 wiring loom?
i can do as close as plug and play as is possible. i'm not cheap with looms though....as i don't piss-fart around and i will need a fair few things to do it right.


if you need it just for a manual its $350......


if its for an auto its $450.


note that if you send me your sierra cluster i will graft in the check engine light and the vss.
Author:  royce [ Fri May 28, 2010 11:04 am ]
Post subject:  Re: Can someone cut the fat from my 1.6 wiring loom?
having done pretty surgery on looms before and knowing how quick the bits needed builds up this is quite cheap!!!!

its certainly not a Sunday arvo job
Author:  Red_October [ Fri May 28, 2010 11:07 am ]
Post subject:  Re: Can someone cut the fat from my 1.6 wiring loom?
PM sent Joe.

royce wrote:
having done pretty surgery on looms before and knowing how quick the bits needed builds up this is quite cheap!!!!

its certainly not a Sunday arvo job


Yup, i'd rather leave auto electrical stuff to people who know what they're doing!
Author:  royce [ Fri May 28, 2010 11:16 am ]
Post subject:  Re: Can someone cut the fat from my 1.6 wiring loom?
the last loom I got stuck into, simple remove all the uneeded shit and add in a heap of extra stuff (wasnt suzuki) was my weekends time for near on 3 months, 24 rolls of tape!!!!
Author:  Red_October [ Fri May 28, 2010 11:21 am ]
Post subject:  Re: Can someone cut the fat from my 1.6 wiring loom?
8O I know if I did it, it would take me two years to modify and once installed, 2 seconds to set the zook on fire :lol:
Author:  Fatzook [ Fri May 28, 2010 11:22 am ]
Post subject:  Re: Can someone cut the fat from my 1.6 wiring loom?
royce wrote:
having done pretty surgery on looms before and knowing how quick the bits needed builds up this is quite cheap!!!!

its certainly not a Sunday arvo job


I did mine on a sunday arvo 8) finished at 2am though :oops:
Author:  Highway-Star [ Fri May 28, 2010 11:29 am ]
Post subject:  Re: Can someone cut the fat from my 1.6 wiring loom?
Red_October wrote:
Also, am I right in presuming that I just hang on to the wiring behind the dash and in the engine bay and nothing from the front seats back?



Just fuel pump wiring. But thats dead easy compared to the rest :D


I got one of those industrial paint bucket things, overflowing with the "Fat" I cut from my 1.6 loom 8O :lol:
Author:  Red_October [ Sat May 29, 2010 7:22 am ]
Post subject:  Re: Can someone cut the fat from my 1.6 wiring loom?
After removing this lot my head hurt so I went in for lunch. I admire anyone that can make sense of this stuff!

Image
Author:  steak_knife [ Sat May 29, 2010 9:02 am ]
Post subject:  Re: Can someone cut the fat from my 1.6 wiring loom?
Speedo head to, Joe will want that & you car will need it.
Page 1 of 1 All times are UTC + 9:30 hours
Powered by phpBB® Forum Software © phpBB Group
https://www.phpbb.com/