| auszookers.com https://auszookers.com/forum/ |
|
| 02 sensor https://auszookers.com/forum/viewtopic.php?f=5&t=13185 |
Page 1 of 1 |
| Author: | drovin [ Wed Jun 30, 2010 10:58 am ] |
| Post subject: | 02 sensor |
which 02 sensor for my g16b, dissy model?? [93 vitara doner]. my wiring diagram clearly shows 4 wires, and the wiring loom also has 4. The problem is all the sellers are telling me its a 3wire sensor for a vitara. Can anyone shed some light on this for me please? |
|
| Author: | steak_knife [ Wed Jun 30, 2010 11:02 am ] |
| Post subject: | Re: 02 sensor |
4th wire may not be used, I don't think thay run a heated O2 in the vit's.. |
|
| Author: | gregdixon [ Wed Jun 30, 2010 11:57 am ] |
| Post subject: | Re: 02 sensor |
The sellers are difficult to deal with if it is not on their wholesalers parts list it doesn't exist to them. I went to multiple car parts shops with an exact part number of my o2 sensor and they said it was the wrong part. After some hunting I found the exact part. If there is a fourth wire it would be used. I doubt suzuki would waste money on extra wire if it is not used. |
|
| Author: | BlueSuzy [ Wed Jun 30, 2010 1:06 pm ] |
| Post subject: | Re: 02 sensor |
Wire costs 2cents not $200.... Have you seen how many spare plugs there is in a loom? |
|
| Author: | steak_knife [ Wed Jun 30, 2010 8:52 pm ] |
| Post subject: | Re: 02 sensor |
BlueSuzy wrote: Wire costs 2cents not $200....
Have you seen how many spare plugs there is in a loom?  Yassss..
http://www.suzistore.com.au/shopexd.asp?id=1667 There is also single wire, & I have seen them go into a 4 pin connector.... |
|
| Author: | BlueSuzy [ Thu Jul 01, 2010 1:29 am ] |
| Post subject: | Re: 02 sensor |
I has a single wire for my Baleno coilpack motor. Goes into a 4 pin plug! |
|
| Author: | drovin [ Fri Jul 02, 2010 1:40 pm ] |
| Post subject: | Re: 02 sensor |
Thats all well and good , but i still dont know which 1 for my g16b dissy |
|
| Author: | gravity_powered [ Fri Jul 02, 2010 2:05 pm ] |
| Post subject: | Re: 02 sensor |
suzistore only list a single wire sensor for a 1.6 http://www.suzistore.com.au/shopexd.asp?id=1667 |
|
| Author: | steak_knife [ Fri Jul 02, 2010 9:57 pm ] |
| Post subject: | Re: 02 sensor |
drovin wrote: Thats all well and good , but i still dont know which 1 for my g16b dissy
How many wire's come out of the sensor, don't worry about the plug cause you could run it through a trailer plug as long as it had a good connection.. The sensor, how many wire's come out of it?? |
|
| Author: | drovin [ Fri Jul 02, 2010 10:13 pm ] |
| Post subject: | Re: 02 sensor |
the vit motor i bought did'nt come with a sensor, so i'm triing to determine what to purchase, ie, 1 wire ,2 wire ,3 wire or a 4 wire, sensor. some how the trailer plug bit went through to the boundry. |
|
| Author: | steak_knife [ Fri Jul 02, 2010 10:22 pm ] |
| Post subject: | Re: 02 sensor |
drovin wrote: the vit motor i bought did'nt come with a sensor, so i'm triing to determine what to purchase, ie, 1 wire ,2 wire ,3 wire or a 4 wire, sensor. some how the trailer plug bit went through to the boundry.
have a look at the sensor's, can you tell us the name of the manufacturer?? Mitsubishi, Denso? As far as I know all the vit's are single wire, could be wrong tho, has happened before.. As for the trailer plug, the number of terminal's on a plug can have no relevance to the amount of wire's used on the sensor, even Ecu's have spare pin's out's...Hence the trailer plug.. 
|
|
| Author: | atari4x4 [ Sat Jul 03, 2010 2:21 am ] |
| Post subject: | Re: 02 sensor |
my vit is a 4 wire stekko? |
|
| Author: | steak_knife [ Sat Jul 03, 2010 4:31 am ] |
| Post subject: | Re: 02 sensor |
atari4x4 wrote: my vit is a 4 wire stekko?
If it is it's heated, so on start up it still work's efficiently.. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|