| auszookers.com https://auszookers.com/forum/ |
|
| Brilliant Idea... https://auszookers.com/forum/viewtopic.php?f=5&t=13918 |
Page 1 of 1 |
| Author: | lump_a_charcoal [ Thu Jul 29, 2010 5:15 am ] |
| Post subject: | Brilliant Idea... |
Ok, I want to make a spring pack the same length as a hilux front 2 inch spring, but soft enough for a trayback sierra. I have some rear OME spring packs (thanks ChrisMac) already. If I were to buy a brand new main leaf from a lux spring pack and use it as the main leaf for the sierra spring pack, would that work? I know the lux leafs are 15mm wider than zook ones, and I need to know the total difference in length, however I can't see why it wouldn't work (assuming these points aren't issues)... Discuss. |
|
| Author: | royce [ Thu Jul 29, 2010 5:27 am ] |
| Post subject: | Re: Brilliant Idea... |
the width difference would make it hard to keep the narrow springs 'in line' and not twist, plus its a headache with new ubolt plates and stuff on the diff plus you might end up with quite an amount of main leaf 'unsupported' at each end, which makes for a prime spot to bend and snap the leaves I think a better idea would be to work out what you need in leaves to make a hilux pack a suitable rate |
|
| Author: | alien [ Thu Jul 29, 2010 6:22 am ] |
| Post subject: | Re: Brilliant Idea... |
as above... for making lux springs the right weight - see the thread on "what shockies do"...( http://www.auszookers.com/index.php?nam ... ic&t=13860 ) i've tried talking to so called spring manufacturers about a lux leaf with sierra rate and theyre all clueless. Atari has recommended a place though which i'll check out. right now i'm running just the top 2 leaves of the hilux front pack in the back of mine and its still stiff - i'm going to cut the lower leaf in half so i just have the mil wrap end u-bolted in, essentially running 1.5 leaves in the rear =P A trac bar is going to be 100% required for you linc... i had wrap when i had 4 leaves in the rear, i'd hate to imagine what theyd do now with 2 leaves =) haha |
|
| Author: | squizzytaylor [ Thu Jul 29, 2010 8:12 am ] |
| Post subject: | Re: Brilliant Idea... |
Any spring maker can make up a main and second to your spec length, width, material thickness and eye size with raised or central eyes, might surprise you how cheap too!! GT |
|
| Author: | alien [ Thu Jul 29, 2010 1:16 pm ] |
| Post subject: | Re: Brilliant Idea... |
^^ not from my experience... well, given i tell them the width, length and spring rate i want (they should know material thickness and number of leaves to achieve that rate). |
|
| Author: | royce [ Thu Jul 29, 2010 8:29 pm ] |
| Post subject: | Re: Brilliant Idea... |
alien wrote: ^^ not from my experience... well, given i tell them the width, length and spring rate i want (they should know material thickness and number of leaves to achieve that rate).
Just give it up ey, squizzy said nothing about spring rate stop the dribble in here |
|
| Author: | alien [ Thu Jul 29, 2010 10:41 pm ] |
| Post subject: | Re: Brilliant Idea... |
lol i just dont understand why its so hard though... ok ill shut up =) |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|