do new bearings and counter shaft. You will hate yourself if you don't change them and its noisy
| auszookers.com https://auszookers.com/forum/ |
|
| Transfer gear install https://auszookers.com/forum/viewtopic.php?f=5&t=14768 |
Page 1 of 1 |
| Author: | DR_JOSH [ Thu Sep 02, 2010 12:08 pm ] |
| Post subject: | Transfer gear install |
I'm looking to install my 6.5's pretty soon, but wanted to make sure I had all my bases covered before getting stuck in. So at the moment I only have the 6.5 gear set, and shifter bushes. What else will I need to pretty much refresh the whole lot, I have never driven it so dont know the current condition but figure I might as well do it while it's apart, Will this cover it, or can I purchase from elsewhere thats cheaper but has only what I need? http://locktup4x4.com.au/suzuki-sierra-89/drivetrain-109/transfer-case-rebuild-kit-393.html I know now I should have just ordered it with my gearset but I really didnt think ahead when ordering |
|
| Author: | TryHard [ Thu Sep 02, 2010 12:38 pm ] |
| Post subject: | Re: Transfer gear install |
Hey man do u already have 6.5 gears in the transferecase ? or did u buy a rebuild the re build kit shouldnt be really hard to install the gears them self are pritty easy to install the instructions from Trilgear are very good...but i do sugest u need a few things u should buy a small press ..from supercheap auto ..also u will need a rattle gun or a big peace of pipe to get the flage nuts off ... thats the hardest bit of the job ... |
|
| Author: | Fatzook [ Thu Sep 02, 2010 12:41 pm ] |
| Post subject: | Re: Transfer gear install |
do new bearings and counter shaft. You will hate yourself if you don't change them and its noisy
|
|
| Author: | TryHard [ Thu Sep 02, 2010 12:43 pm ] |
| Post subject: | Re: Transfer gear install |
Fatzook wrote: do new bearings and counter shaft. You will hate yourself if you don't change them and its noisy
i think i changed everything in my transfer case and its still noisy lol tough thats in 3rd gear and above |
|
| Author: | Fatzook [ Thu Sep 02, 2010 12:46 pm ] |
| Post subject: | Re: Transfer gear install |
Sure its not your gearbox?? |
|
| Author: | TryHard [ Thu Sep 02, 2010 12:48 pm ] |
| Post subject: | Re: Transfer gear install |
Fatzook wrote: Sure its not your gearbox??
yer man wasnt noisey untill i put gears in it dont bother me that much u can just here it wind up so the speak anyways enuf about me |
|
| Author: | Fatzook [ Thu Sep 02, 2010 12:49 pm ] |
| Post subject: | Re: Transfer gear install |
if you have already put gears in it, then thats why its noisy. The 5.14's and up tend to whine alot more. Just drive it 
|
|
| Author: | TryHard [ Thu Sep 02, 2010 12:58 pm ] |
| Post subject: | Re: Transfer gear install |
Fatzook wrote: if you have already put gears in it, then thats why its noisy. The 5.14's and up tend to whine alot more.
Just drive it i got 6.5s |
|
| Author: | Fatzook [ Thu Sep 02, 2010 1:02 pm ] |
| Post subject: | Re: Transfer gear install |
yeah they all whine. Haven't seen a 6.5 yet that hasn't been quite vocal 
|
|
| Author: | DR_JOSH [ Thu Sep 02, 2010 1:06 pm ] |
| Post subject: | Re: Transfer gear install |
TryHard wrote: Hey man do u already have 6.5 gears in the transferecase ? or did u buy a rebuild the re build kit shouldnt be really hard to install the gears them self are pritty easy to install the instructions from Trilgear are very good...but i do sugest u need a few things u should buy a small press ..from supercheap auto ..also u will need a rattle gun or a big peace of pipe to get the flage nuts off ... thats the hardest bit of the job ...
I havent even opened the transfer yet, I have all the tools side of things covered I'm pretty sure if not my mates workshop is not far away. I just wasnt sure what else I should be replacing while I had it open. I think I'll just get a bearing kit to be on the safe side, do it with the gears |
|
| Author: | jonno_racing [ Thu Sep 02, 2010 1:15 pm ] |
| Post subject: | Re: Transfer gear install |
Fatzook wrote: yeah they all whine. Haven't seen a 6.5 yet that hasn't been quite vocal
mine are/were beffore i filled my transfer with water. |
|
| Author: | jonno_racing [ Thu Sep 02, 2010 1:16 pm ] |
| Post subject: | Re: Transfer gear install |
u got a bearing puller?/press 2? |
|
| Author: | hooki [ Thu Sep 02, 2010 2:00 pm ] |
| Post subject: | Re: Transfer gear install |
a press will make it 100 times easier. I got one from super cheap when they had a sale....$49 
|
|
| Author: | 89_tintop [ Thu Sep 02, 2010 6:56 pm ] |
| Post subject: | Re: Transfer gear install |
Contact weaves on hear regarding bearings.. Cheap as and top quality.just got mine through him and he was about $40 cheaper for a ferret quality product. |
|
| Author: | DR_JOSH [ Thu Sep 02, 2010 8:17 pm ] |
| Post subject: | Re: Transfer gear install |
can you buy just the gaskets from anywhere? All I can find is rebuild kits with gaskets and bearings |
|
| Author: | 31zook [ Thu Sep 02, 2010 8:35 pm ] |
| Post subject: | Re: Transfer gear install |
just use gaskit goo.... yes weaves is allot cheaper then most i tend to use him for everything even things that don't really relate to bearings
press is a great idea, but if you put one end of the shaft on some wood and have a rubber mallet, and think about what your doing, it can be done that way
last 2 times i rebuilt a Tcase i only used my press once and my bearing puller the rest. |
|
| Author: | lump_a_charcoal [ Thu Sep 02, 2010 10:51 pm ] |
| Post subject: | Re: Transfer gear install |
I would replace the front output shaft with the beefier version, not sure if it is necessary though. Also, paper gaskets are supplied. |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|