| auszookers.com https://auszookers.com/forum/ |
|
| need help gearstick https://auszookers.com/forum/viewtopic.php?f=5&t=16687 |
Page 1 of 1 |
| Author: | spuki [ Thu Nov 11, 2010 11:11 pm ] |
| Post subject: | need help gearstick |
well the idea was to try and pull the motor and gearbox out in one, so today i went to figure out how to remove the gearstick, i removed the knob, the bottom plate with 3 bolts, the washer under that and found the bush under that had perished pretty bad and as i was pulling that out the stick come out, wasn't sure if it was meant to come out so easy?, anyway my problem now is that i went to put the stick back in to make sure it was as easy as that and try to select some gears, stick goes in fine, feels like its in neutral, but wont select any gears? have i done something wrong? broken something? i dont have a bush in there or the plate bolted down but still thought it should select gears |
|
| Author: | royce [ Thu Nov 11, 2010 11:13 pm ] |
| Post subject: | Re: need help gearstick |
was it in neutral when you pulled it out? sounds like you are putting it in off to teh side of the gates, peer into the hole and youll see the slot it goes into, its not easy but it goes in |
|
| Author: | spuki [ Thu Nov 11, 2010 11:21 pm ] |
| Post subject: | Re: need help gearstick |
yeah was in neutral when i pulled it out, and i will have another go but deffinately feels like its going in correctly |
|
| Author: | Kermy87 [ Thu Nov 11, 2010 11:51 pm ] |
| Post subject: | Re: need help gearstick |
Try Spinning the output shaft to the box wilst trying to select a gear |
|
| Author: | spuki [ Fri Nov 12, 2010 12:07 am ] |
| Post subject: | Re: need help gearstick |
still wont go into gear..? |
|
| Author: | Kermy87 [ Fri Nov 12, 2010 12:19 am ] |
| Post subject: | Re: need help gearstick |
Have you got the box off the motor |
|
| Author: | zooky08 [ Fri Nov 12, 2010 12:20 am ] |
| Post subject: | Re: need help gearstick |
look in the hole and there shaft on both sides of the shaft that the gear stick goes into. make sure the side shaft thingy is pulled right back as far as it can go, then try |
|
| Author: | atari4x4 [ Fri Nov 12, 2010 12:24 am ] |
| Post subject: | Re: need help gearstick |
have a look at the pics in this thread, it will give you an idea of lining up the shift rails. http://auszookers.com/index.php?name=Fo ... ifter+bolt |
|
| Author: | spuki [ Fri Nov 12, 2010 1:15 am ] |
| Post subject: | Re: need help gearstick |
cheers zooky and atari, got it, was actually in third :/ much appreciated guys |
|
| Author: | suzukilwb [ Fri Nov 12, 2010 1:21 am ] |
| Post subject: | Re: need help gearstick |
you can undo the 4 bolts that hold the gear stick houseing in and (tap) it off with a hammer makes it easer to get the screw driver in to make the gates line up |
|
| Author: | spuki [ Fri Nov 12, 2010 1:34 am ] |
| Post subject: | Re: need help gearstick |
yeah thats actually what i ended up doing, should of i put like a gasket gue or something on it before i put it back on? |
|
| Author: | suzukilwb [ Fri Nov 12, 2010 12:11 pm ] |
| Post subject: | Re: need help gearstick |
ummmm i didnt know maybe take it for a spin if it leaks take it back off and put some on but i think it should be right |
|
| Page 1 of 1 | All times are UTC + 9:30 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|